A solution for the vertically challenged rider-A Drop Seat Kit

You have finally made the decision to purchase a Harley-Davidson Touring bike and because of your shorter stature it doesn’t quite fit. You look into lowering the bike but decide you need more than the factory lowering kits can offer. Well go ahead and get that paperwork signed because K and G Cycles (www.kandgcycles.com) has exactly what you need to make that bike fit. A 3.5″ Drop seat Kit from Bagger-Werx that is sure to make that new ride manageable. Designed to work on the new chassis and frame of the 2009 and newer models, this kit has just about everything you need to complete this custom install.

PA-501002 drop seast kit offers a lowe seat height with no change in ride.* Bolt-on kit with no cutting or welding involved – makes installation a breeze
* Drops the seat rail height a full 3.5 inches on Touring models without changing the bikes stock ride height and ground clearance – won’t compromise ride integrity
* Get the slammed look that you are after without sacrificing the handling and clearance of lowering kits – plants you firmly in the pocket
* Fender, fender struts and saddlebags remain at the stock height and location, only the seat area drops down. Note: All Harley accessories attachable and detachable fit in their stock locations
* The kit can be installed in approximately 3 to 4 hours. The re-designed battery/ABS tray permits quicker installation without the need to disconnect or bleed any Brake lines….. saving time and money
* The kit allows the EVAP emissions cannister fitted to models sold in California, to remain on the vehicle
* This kit does eliminate the OEM saddlebag guards and rails. Note: On models equipped with OEM rear saddlebag guards and rails that are no longer used, optional saddlebag guard kits are available through PAUGHCO S Bagger-Werx.
* Each kit includes a fully-assembled gloss Black powdercoated rear section, battery box, fuse box, negative battery cable, left and right side frame Covers, a 2-up custom seat, and all necessary hardware with a detailed instruction manual

You can have it all, a Touring bike that fits, a wicked profile and attitude, and stock ride height and suspension travel that retains the original comfort. K and G Cycles is proud to offer you the chance to transform your 2009-2013 HD Touring class bike into a ride that fits. Contact K and G Cycles (www.kandgcycles.com) to pick up your 3.5″ seat drop kit today, so you can enjoy your ride tomorrow.

I3.5 drop seat kit makes owning an HD touring bike more fun.MPORTANT: You should check the tire manufacturers specifications and your Harley-Davidson service department recommendations before ordering and installing a low profile tire on these models.

Special Note 1: If you have a 2010 thru 2012 CVO STREET GLIDE FLHX or CVO ROAD GLIDE ULTRA FLTR motorcycle, the PAUGHCOS Bagger-Werx Drop Seat Kit should not be installed as it will cause the rear tire to rub on the battery box which could lead to serious injury or death. These models are equipped with an 18″, high profile rear tire. We do not recommend doing so but possibly using a lowprofile 18″ rear tire such as Metzeler or another brand rear tire may afford enough clearance to allow for installation of the PAUGHCOS Bagger-Werx Drop Seat Kit on these models.

Special Note 2: If you have a 2010 thru 2012 CVO STREET GLIDE FLHX or CVO ROAD GLIDE ULTRA FLTR equipped with adjustable rear shocks, it will be necessary to replace them with Harley-Davidson air shocks (OEM #54565-09). This air shock must be used to replace the FL CVO adjustable non-air shock before installing PAUGHCOS Bagger-Werx Drop Seat Kit.

Special Note 3: PAUGHCOS Bagger-Werx highly recommends that the PAUGHCOS Bagger-Werx Drop Seat Kit be installed by a qualified Harley-Davidson technician. Note: If there have been any changes from the OEM stock rear wheel, tire or shocks, it is the responsibility of the installer to check all clearances when installing the Bagger-Werx Drop Seat Kit.

You can have it all, a Touring bike that fits, a wicked profile and attitude, and stock ride height and suspension travel that retains the original comfort. K and G Cycles is proud to offer you the chance to transform your 2009-2013 HD Touring class bike into a ride that fits. Contact K and G Cycles (www.kandgcycles.com) to pick up your 3.5″ seat drop kit today, so you can enjoy your ride tomorrow.