Adding a Velocity Stack improves Looks and Performance

velocity stack kit 34-1174

What is a Velocity Stack and what are the benefits of running one on our bike? That is a great question, and The K and G Cycles Team (www.kandgcycles.com) is going to do their very best to provide you with enough information to answer that. So sit back and prepare to have your knowledge expanded. In simplist terms a velocity stack is a trumpet-shaped device of differing lengths which is fitted to the air entry of an engine’s intake system, carburetor or fuel injection. It is designed to:

  1. Allow smooth and even entry of air at high velocities into the intake tract with the flow stream adhering to the pipe walls. (Sort of like a supercharger without the cost)
  2. Modify the dynamic tuning range of the intake tract by functioning as a resonating pipe which can adjust the frequency of pressure pulses based on its length within the tract. (High Tech talk for improving the flow of air across the board for better response and more usable power.

Modervelocity stack graph 1n engines universally have tuned intake tract volumes and associated resonance frequencies, designed to provide higher than atmospheric intake air pressure while the intake valves are open – increasing the density of the trapped air in the combustion chamber (higher compression). Modified engines often have the original air box and associated ducting removed and velocity stacks are installed as accessories. Todays fuel injection systems with a plenum and single air inlet typically incorporate some sort of radiused entrance, designed to improve power, based on air flow increases. Power gains are usually at higher rpm. In amateur and professional racing, aftermarket velocity stacks are often used, as rules allow, and gains in the order of 2% to 4% can be obtained when inlet radii and stack lengths are optimized for that engine. The length of the stack is known to have a direct effect on a particular engine’s boosted power range.

It is comTurbo Velocity stack 34-1204 monly related that “stand off” (air–fuel mix that gets pushed back out of the port, usually at full throttle / low rpm) is somehow captured by installing a longer intake pipe (stack). but, it is actually that the intake valve is closing too late and the combustion chamber is simply overfilling and blowing back out the intake port, before the intake valve closes. A longer inlet pipe will create a later intake pressure wave that will help keep the air in the chamber until the intake valve closes.

The acceleration of air flow iVelocity_stack_detailnto a duct is inherently a highly efficient process and the difference between even the crudest radius inlet, and the most aerodynamic shape possible is slight, amounting to no more than a few percent The flow coefficient of a perfect entry would be 1.0 while the coefficient for a sharp edged entry would be 0.6 and a re-entrant plain pipe 0.5. In practice these latter types of entry are never used for engine intakes. There is always some attempt to provide some radius at the entry. ThS&S Velocity stack 34-1880 is means that total engine airflow would not increase by the amount suggested by these figures, which apply only to the entry alone, as the inlet end is never the smallest or most restrictive part of the system. Because the greatest losses to flow occur near the valve seat, actual overall gain from any improvement of the entry flow would be much less. In the real world, on high-rpm Internal Combustion engine, using a minimum amount of inlet radius gives the best wave strength and a power boost of 2% to 4% over a 3000 to 3500 rpm range. Using a larger radius, like 3/4″, broadens out the resonant pressure wave rpm range, but the compression boosting pressure wave is greatly diminished and almost unnoticed by the engine.

 I suspect one of thcustom filtered velocity stack cc-629371e main reasons many of us will buy a velocity stack is for its raw, high performance looks. I do not feel those are bad reasons, but I do feel it very important to show you there are actual benefits reaped from installing one. At K and G Cycles (www.kandgcycles.com) we offer an amazing range of Velocity Stacks for you to choose from. Short neck, long neck, filtered, non-filtered, custom application or stock drivelines, we’ve got a velocity stack that will satisfy your needs. Contact us today, and be on your way to better look and performance in no time.