V-Twin Manufacturing

WR narrow type 45 2.5 gallon gas tank set features a raw finish. Tank has 2-3/8 NPT fittings on each side the left 1-1/4 gallon for the gas and the right 1-1/4 gallon for the oil. Tank uses two vented gas caps which are not included. Does not accept reserve fuel shut off rod or instrument dash panel assemblies. Both sides are intended for gas if oil tank is under seat ares but can be refitted to use gas on the left and oil on the right. Order required oil feed vent and return lines and oil return pipe kit mount kit 1936-46 shift gate plugs and caps separately. Right side
38-0497" WR narrow type 45 2.5 gallon gas tank set holds gas on both sides and features raw finish. Tank set has 2 3/8 NPT fittings on each side for gas and oil lines. Tank uses two vented gas caps which are not included. Does not accept reserve fuel shut off rod or instrument dash panel assemblies. Both sides are intended for gas but can be refitted to use gas on the left and oil on the right. This application required oil feed vent and return lines and oil return pipe kit available separately. Right side for oil will require oil a stand pipe with 3/8 NPT outside and 1/4 NPT inside
38-0498" Vented billet Krome Kap kit only features two caps. 1936-1952 W 1941-1952 WR

Legacy style 3.8 gallon gas tank with stock screw bung gives functional styling and improves rider comfort. Fully pressure tested will accept late model 2007 and up OEM fuel pump and fittings. Replaces stock tanks #61348-07 and #61405-07. Order gas cap separately. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 2007-UP XL EFI models

Fuel tank console door features a black finish which is powder coated black. 2008-UP FLT

Chopper style gas tank has a 2.5 gallon capacity and features a forward and high gas cap opening for screw-in type gas caps.
Please test fitment before painting. Tank weld seams may require filler to meet your individual requirements. Do not grind or sand the seams or joints, as this may cause leaks. We suggest using Kreem gas tank combo kit to clean, condition and seal. This will help to stop leaks and prevent corrosion. Check petcock opening, making sure the petcock can be easily installed. Petcock fitting should be masked or plugged during painting for easy installation of petcock. The front edge to the mounting holes measures 15", the front bottom edge to the upper mounting holes measures 3-1/4" and center to center from the front to rear mounting holes measures 18".

Top Length: 17"
Bottom Length: 15-1/4"
Rear Width: 4-3/4"
Front Width: 9"
Rear Height: 1-3/4"
Front Height: 7-5/16"
Front Tunnel Height: 3-1/4"
Rear Tunnel Height: 1/2"

Custom application

Shift gate screw is 5/16 -24 thread and features a chrome finish. Sold as a pair. 1936-1946 EL 1936-1946 G 1936-1946 W 1941-1946 FL

Chrome front axle nut cap set includes one cap with internal hex to secure to axle nut for 25mm axle. Caps are machined to allow more thickness to prevent set screw threads from stripping. 2007-2017 FXST except 2002-up VSRC, FXCW, FXCWC, FXSTD 2008-UP FLT 2008-2017 FXD 2008-UP XL

Red reflectors for license plates are original glo-brite style with real glass. Custom application

Linkert snap throttle kit is for use with 1 custom bars. This kit includes snap kit 1/4 fast throttle assembly grips cable and cable end. Original Flanders style replica of the 1940's. Originally designed to be used with the Hellings-Stellings handle bar conversion. The 1 handle bar conversion and rubber mounted Flanders risers allowed a vibration reduction alternative for the Spring Fork models of the 1940's. Snap throttle kit is for 1936-65 OHV conversion models with the brass linkert carburetors. Cable must be cut to length for each specific application. 1936-1952 EL 1941-1965 FL

Throttle and idle cable set in braided stainless steel with a black coat is stock length. The casing length is 43 for the idle cable and 39-1/2 for the throttle cable. Stainless steel braided with a black coat throttle and idle cable set includes the switch control and a 90° elbow fitting with PVC coating. The stainless steel braid is tightly woven for a bright quality consistent finish. The black coat is UV resistant heat bonded non yellowing grade for a long service life. 2002-2007 FLH with cruise control

V-Twin black throttle cable has a 38 casing length with 90° elbow fitting. The cable measures 42.5 in length. Includes 90° elbow fitting. The ball end is 4.5mm. 0-Replacement application cable for 38mm Mikuni carburetor

Overhaul kit for 1-1/2 carburetors includes throttle shaft brass float needle and seat float bushings springs float pin gasket carburetor bowl large nut with stud lock washer luck nut and copper filled seal washer. For M74 models. Threads on this needle and seat assembly is 7/16 x 27. *NOTE: For the float arm installation the center prong of the float arm should have .003 of clearance in order for the arm and needle to move freely. 1941-1965 FL 1941-1952 EL

Pingel chrome metric hex petcock features down spigot 3/8 National Pipe Thread without nut. Designs are made for a seated position on the motorcycle with the hose outlet facing a direction to ease fuel line hookup. Petcock features a universal configuration that can be used in almost any tank location and the valve can be installed with hose barb pointing in any direction. This leaves the on/res/off lever accessible. 1965-1974 FL 1971-1974 FX 1955-1974 XL

Linkert carburetor main nozzle is machined of solid brass for use with 1-1/2 Bombsight venturi's. 1941-1965 FL

Linkert carburetor atomizer with screen. 1941-1965 FL

Dual cable throttle housing features threaded cable inserts for dual cable push pull operation applications in a black finish. *NOTE: Must order the dual type handlebar throttle tube separately. 1981-1999 FL

Parkerized intake manifold nuts with brass seals. Note: For use with a 3-bolt 61 manifold on large port knuckleheads. Note: The seals are thicker than stock and the nuts fit these seals only. 1941-1947 FL

Carburetor rebuild kit for Mikuni carburetor includes flow fuel hose throttle valve seal float bowl seal o-ring and carburetor top gasket. Custom application for HSR-42/HSR-45 carburetors

Kit includes brass jets and instructions designed specifically for each model listed. The kit features No Drilling installation and will work on stock to heavily modified engines. 1988-2003 XL

S&S L series carburetor master rebuild kit includes the throttle shaft and plate hardware gaskets springs idle mixture screw needle and seat assembly.

NOTE: Built-in choke mechanism. Intermediate jet goes through ventruri from top of carb down into main discharge tube. Changeable intermediate air bleed screws into boss adjacent to intermediate jet on top of carb. Side mounted float bowl. Air cleaner mounting pattern same as stock Tillotson Bendix Keihin butterfly type carbs. 0-Replacement application for S&S L" series carburetor"

Natural finish 40mm CV carburetor is for 1340 models and is an accurate reproduction of the Venerable Keihin CV carburetor. Includes two manifold seals one spigot seal and a choke bracket to mount on top of the carburetor cover 1.6 main jet and 0.46 slow jet. Must order related components separately: cables manifold choke cable and air cleaner is not included. *NOTE: Order jet assortment separately. Carburetor includes bracket for dual push-pull throttle and idle cable installation. Early applications will allow use of a single pull throttle installation as the throttle idle
35-0612" CV master carburetor rebuild kit fits 1989-up models with CV carburetors. 1988-2006 XL 1200

Natural finish 40mm CV carburetor is for 1340 models and is an accurate reproduction of the Venerable Keihin CV carburetor.
Includes 1.9 main jet and a .046 slow jet installed. Must order related components separately: cables, manifold, choke cable and air cleaner is not included.

*NOTE: This CV carburetor is made with V-Twin MFG.'s exclusive tooling in Taiwan.

OEM Spec. 27492-96

FLH 1985-2007
FLST 1984-2006
XL 1986-2006
FXD 1991-2006
FLT 1988-2007
FXST 1986-2006

Retrofit fuel line kit includes a pre-formed 17 x 5/16 black fuel line needle and seat inlet assembly with 90° swivel fitting hose clamps and a float bowl gasket. Fuel line kit for use upgrading early S&S Super E and G carburetors with a 90° fuel hose. Custom application for S&S Super E and G carburetors

Linkert carburetor float bowl with early style hex cap features a natural aluminum finish and is the bean pot style with additional capacity. *NOTE: Float bowl with drain screw includes installed stainless steel needle with matching brass seat assembly installed black unsinkable nitrophyl linkert float with our unique 1 piece float arm in brass for smooth action and pivot pin with two caps. Larger inner diameter adds 1.45 cubic inches to hold additional fuel. Extra capacity for racing applications has external bow hex cap. Has 9/16 x 20 hex plug at needle valve opening. Fits all
35-0284" Replica Linkert carburetor cork float includes shoulder bolt and screw. This cork float manufactured to OEM specifications and helps maintain a proper level of fuel in the carburetors float bowl for optimum performance. *NOTE: Sold as a pack of 5. **NOTE: Not for use with oxygenated fuel. 1937-1948 UL 1936-1952 W 1936-1957 G

Tillotson carburetor parts kit includes the fuel inlet adjustable needle kit tickler kit idle mixture screw base pump needle and seat gasket and hardware kit. Kit is for use with Tillotson carburetors only. Parts are packaged inside a V-Twin decorative tin. 1966-1970 FL 1966-1971 XL

EFI 90° forward mount air cleaner kit with tapered air filter. Includes hardware and gaskets. 2008-2013 FLT

Odins mirror set features curved mirrors with offset stems Set includes left and right. Black mirror featuring die cast construction. 1965-UP All models for left and right side application

Wyatt Gatling assembly includes chrome sweeper air cleaner integral breather system with bracket and mounting kit. For use with CV carburetors. Includes filter element. DIY easy install bolt-on assembly has no hoses to connect! 1993-2007 FXST 1993-2007 FXD

Chrome billet apache style tear drop mirror set with offset stem. 1965-UP All models for left and right side application

Wyatt Gatling inverted air filter kit mounts with center screw. Filter is round type and fits Screamin Eagle and Wyatt Gatling with 3 stud mounting. Kit includes tapered inverted air filter 3 studs for mounting cross bar and a 5/16 X 18 X 3/4 button head screw for attaching to center mount bracket. Inverted design allows for more air flow! For use with appropriate backing plate for specific application. NOTE: For all tapered air filter applications with 3 stud mounting. 0-Replacement for V-Twin #34-1365 Wyatt Gatling Air Cleaner Assembly 0-Replacement for V-Twin #34-1255 Cycovator Hi-Flow Air Cleaner Kit

Finned style bird deflector is cast of aluminum and chromed. The cover fits Bendix and Keihin carburetors and includes three 1/4-20 UNC x 1-1/2 socket head cap screws. There is no provision for a filter on this cover. 1975-1987 FL 1980-1987 FX 1971-1987 XL