V-Twin Manufacturing

Twin Cam chain shoe tool is used to remove and replace the spring-loaded cam chain tensioners. Saves hours of the mechanic's time!

*NOTE: Must order chain tensioners and related components as required.

1999-2006 FL
2000-2006 FLST
2000-2006 FXST
1999-2005 FXD

0-Front

Rigid axle adjuster kit is for use with a 3/4" axle on rigid or hardtail frames with 7/8" slots. Includes black 2-3/4" x 24 x 3" adjusters and machined chrome axle blocks. Adjuster blocks go on the outside of the frame axle plates to use adjusters in existing threaded bosses. *NOTE: Requires at least a 12" long x 3/4" axle. 1941-1957 FL Custom application with use of a 3/4" axle on Replica rigid frames"

Black fishtail muffler set without baffles features a 3" body outer diameter and is for M8 models. Sold in a quantity of 2.
**CAUTION: These exhaust products are not legal for sale or use in California on pollution-controlled vehicles. These products are intended for non-highway only.

2017-UP FLT

Length 34-1/2"

Polished oil collector is designed to collect the oil mist from the breather hose which eliminates engine oil from collecting in air cleaner. On top is a high flow air filter that acts as a baffle allowing the oil and air to separate more efficiently and can easily be cleaned. On the bottom is a drain plug to allow drainage on a regular basis. A 90° barbed fitting fits breather hoses perfectly and includes chrome mounting billet clamp. *NOTE: Order strp steel clamp if prefered ehich can then be cut to length. *NOTE: So the clamp does not slip when you tighten the fittings it's s
40-0569" Liquid filled 60lb oil pressure gauge features a silver face stainless steel case chrome rim and weather resistant sealed lens. This liquid filled face eliminates needle bounce giving a constant reading. Gauge has a 1/8 National Pipe Thread male rear fitting. Custom application

Saddlebag latch rivet tool gives secure fastening of rivets while providing a clean factory look. Use to crimp saddlebag latch and hinge rivets. 0-All Models

Universal 18" chrome heat shield for use on 2" exhaust pipes. Includes clamps for installation. Custom for 2" pipes"

Chrome 2 into 1 exhaust lake style header pipes are designed to look like the hot rod side exhausts with 12mm oxygen sensor bungs. Includes heatshield and hardware. The turn out end is 3 in diameter. Fits with controls only. Header pipes are 1-3/4 with 16 gauge steel construction. Accepts 12mm oxygen sensor units bungs may be plugged for earlier applications. Will also work on many Rigid Chopper and Bobber models with left side drive.

**NOTE: These pipes will not work with floorboards. Collector is not baffled.

2012-2017 FXST
2012-2017 FXDWG

Sifton wrist pin bushing reamer tool is easy to use with their design lead in taper at the start of each ream. Order rod clamping tool separately. This tool is used to secure the rod while performing the reaming operation. The front of the taper is .767 body for actual reamed hole is .792 . 1936-1952 EL 1941-1984 FL 1985-1999 FL 1937-1952 WL 1937-1973 G 1937-1948 U

Ironhead LAF style header set features a chrome finish. *NOTE: Pipes attach to each other at the end. Additional mount bracket may be fabricated to mount set to frame. 1957-1985 XL

Indian Scout short type drag pipe set features a black finish with straight pipes with white exhaust wrap. Pipe set is finished in heat proof black.

*NOTE: Pipes are equipped with O2 sensor ports.
*NOTE: Pipe set can be baffled with insert, available separately.
**NOTE: UPS may consider this part as packaged "oversize" for shipment, as compared to the actual weight, which will result in higher shipping costs.

2015-UP Scout

Black 1-1/4 handlebar is knurled and drilled for internal wiring. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 1974-1981 FL 1974-1981 FX 1974-1981 XL

Final drive steel 27 tooth front pulley. *NOTE: Must order nut and lock kit separately. 1991-2003 XL 883, 883C, 883 HUG, 883R

York Softail rear chain kit is for 5 speed models. Stock ratio is supplied with steel sprockets 22 tooth front and a 48 tooth rear with 120 link chain. Conversion kit includes everything needed to convert 1987-2006 5 speed belt drive system to a heavy duty530 chain drive. This kit is for a stock size rear tire. Chain will have to be cut to length breaker and master link included.
*NOTE: Use existing pulley spacer behind the transmission 22 tooth sprocket. When using a 21 tooth front sprocket: 48 tooth rear sprocket = 4% deeper (faster acceleration) 49 tooth rear sprocket = 6

19-0172 49 tooth splined engine sprocket is nickel plated. Can be used with 530 chain. *NOTE: For JD 2.5 mph change per tooth upon down.

1987-1999 FLST
1987-1999 FXST

Black rear 16 X 5 wheel rim. Our spoke set with 20 short and 20 long shank spokes can be used. This rim has a small center valve stem hole to accept metal stems.
Requires the separate purchase of a spoke set VT-45-0946.

2009-UP FLT

21 sissy bar features the one piece bolt on design in a gloss black finish. Round sissy bar with the upper kick angle mimics the old school look of the 50-60's bobber style sissy bars. *NOTE: The required docking hardware and turn signal relocation kits must be ordered separately. 2006-2017 FXD except FLD, FXDF, FXDFSE and 2010-2017 FXDWG

0-Front

Indian Scout rear brake disc features a polished stainless steel finish. 2015-UP Scout

FXD 2:1 lake side pipe exhaust features a black finish.
Exhaust pipe features a 1-3/4" diameter at the cylinder head and a 2" diameter before collector.

*NOTE: Exhaust header set is painted black but has oxidation (rust) on the inside. The installer may have to re-paint the pipe set, inside and outside. We recommend using VT-41-0125. VHT Flame Proof 1350 Black, to coat the inner and outer surfaces of the header pipes.

**NOTE: Pipe has 18mm O2 sensors.

*NOTE: Unbaffled

*NOTE: Needs forward controls

FXD 2006-2017

Sissy bar measures 20 high x 7-1/2 wide and accepts insert. 2004-UP XL with rigid side plates 2002-2005 FXD equipped with either rigid or detachable side plates

This complete kit contains the docking hardware needed to install detachable accessories with docking points for sissy bars and luggage racks. 2018-UP FLHC 2018-UP FLHCS 2018-UP FLSL 2018-UP FXBB 2018-UP FXFB 2018-UP FXFBS 2018-UP FLSB 2018-UP FXLR 2018-UP FLDE

Black outer primary cover with smooth flat finish. Fits all DYNA models with mid controls. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 2007-2017 FXD

Chrome steel with black mesh 3 hole outer primary derby cover. 1970-1984 FL 1971-1984 FX 1984-1984 FXST 1985-1998 FXST 1986-1998 FLST 1984-1984 FLT 1985-1998 FLT 1991-1998 FXD 1984-1984 FXR 1985-1994 FXR

Solid motor mount kit for swingarm and hardtail frames features a natural alloy construction and finish. Kit replaces stock ISO-rubber mounts from 2004-up Sportster models This 6 piece set includes replacement motor mounts and 2 covers with hardware for the outside of the rear mounts. These mounts eliminate the shake while the motor is running. Great for hardtail applications to stop the rear chain slap! *CAUTION: bike shoule be on lift to support the motor's weight during installaiton. Works best with 2 people. *NOTE: Now you can feel the torque! 2004-UP XL

Slash slip-on muffler set includes removable baffle set. One bolt for a quick removal. Features a 2-1/2 body with a black finish. Install with stock header pipes and features 1-3/4 inlet with channel mounting. The diameter where the body attaches is 1.93 . For performance quality and sound there is nothing else like a V-Twin slip-on muffler! **CAUTION: These exhaust products are not legal for sale or use in California on pollution controlled vehicles. These products are intended for non-highway only. Custom application

8.5 mini ape hanger handlebar features a black finish. 1974-1981 XL

Black 1-1/4 handlebar features throttle by wire right side notches and has holes with a copper wire inside for pulling thru internal wiring. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 2008-2014 FLTR

Conversion kit includes everything needed to convert the belt drive system to heavy duty 530 chain drive. Stock ratio is supplied with a 24 tooth front sprocket and a 51 tooth rear sprocket. This kit is for a stock size rear tire. Chain will have to be cut to length breaker and master link included. *NOTE: Use existing pulley spacer behind the transmission 22 tooth sprocket. When using a 21 tooth front sprocket: 48 tooth rear sprocket = 4% deeper (faster acceleration) 49 tooth rear sprocket = 6.5% deeper and 51 tooth rear sprocket = 10.5%
19-0180" Conversion kit includes everything needed to convert the belt drive system to a heavy duty 530 chain drive. Stock ratio is supplied by a 24 tooth front sprocket and a 51 tooth rear sprocket. Chain will have to be cut to length breaker and master link included. 2000-2006 FLST 2000-2006 FXST

34 tooth solid compensator kit reduces noise and improves engine starting along with starter life. Also aids in better throttle response and smoother shifting due to the reduction in weight. For use with M8 models. Easy to install no other parts needed. *NOTE: Instructions included. 2017-UP FLT

Jims left main bearing oil seal installer assists with perfect installation and adds the advantage of allowing the alternator stator to remain in place during operation. For M8 models.

*NOTE: When the seal is installed properly there will be some bottoming out.

2017-UP FLT
2018-UP FLST
2018-UP FXST

Muffler header gasket set for M8 models. Sold as a pair. 2018-UP FLFB 2018-UP FLFBS 2018-UP FLSL 2018-UP FLDE 2018-UP FXBB 2018-UP FXLR 2018-UP FXBR 2018-UP FXBRS