All

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 26", length 45", Each, travel 2 3/4", Harley 87-06 FX 87-06 FL 86 - 13 XL

• Black rubber straps
• Can install or remove without tools
• Length is measured from hook end to hook end
• See below for availability of one or two piece strap

V-FACTOR
Non-Ribbed Two-Piece, 10 1/2 Long with a Quick Disconnect
Fits Softail Late 1993/1999
Replaces HD# 66109-93 & 66111-93

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 26", length 50", Harley 87-06 FX 87-06 FL 86 - 13 XL

• 50 amp rated heavy duty cables to be used as battery, starter or solenoid cables
• eature copper core with insulated ring terminals for performance and safety
• All cable lengths are measured from center to center of eyelet holes

Sumax
10 Pack Assorted Cables
8 ¹/₂ Length (4 Each), 11 Length (4 Each), 15 ¹/₂ Length (2 Each)
⁵/₁₆ & ⁵/₁₆ Bolt Hole Sizes

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 26", length 52", Each, travel 2 3/4", Harley 87-06 FX 87-06 FL 86 - 13 XL

• Recommended for high compression engines
• 1,661 individual 36 gauge tin coated copper strands strategically woven for maximum current flow
• High performance battery cables will increase starter performance by supplying maximum battery current to the starter motor
• Offer you a custom braided stainless appearance with an ultra-flexible translucent jacket that is oil & gas resistant and rated at 287° while providing excellent performance and show quality good looks
• Kits include one battery positive terminal to starter motor cable and one battery negative terminal to ground cable
• eatures:
  • Copper ends with corrosion resistant Zinc Plating
  • Electrolytic-Grade copper strands
  • The look of braided stainless steel
  • All cables have one ⁵/₁₆ I.D. end and one ¹/₄ I.D. end
  • Cable ends are crimped on and include waterproof heat shrink
  • 4 gauge for high performance
  All Balls
  7 Individual Cable

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 26", length 80", Harley 87-06 FX 87-06 FL 86 - 13 XL

• Recommended for high compression engines
• 1,661 individual 36 gauge tin coated copper strands strategically woven for maximum current flow
• High performance battery cables will increase starter performance by supplying maximum battery current to the starter motor
• Offer you a custom braided stainless appearance with an ultra-flexible translucent jacket that is oil & gas resistant and rated at 287° while providing excellent performance and show quality good looks
• Kits include one battery positive terminal to starter motor cable and one battery negative terminal to ground cable
• eatures:
  • Copper ends with corrosion resistant Zinc Plating
  • Electrolytic-Grade copper strands
  • The look of braided stainless steel
  • All cables have one ⁵/₁₆ I.D. end and one ¹/₄ I.D. end
  • Cable ends are crimped on and include waterproof heat shrink
  • 4 gauge for high performance
  All Balls
  8 Individual Cable

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 31 1/2", Each, Harley 06-16 FX 07-16 FL
Our batteries are made in the USA by Yuasa (except those noted with Import below). They are the same batteries that are made forHarley-Davidson^®. Our POWER HOUSE Standard line features patented separators that allow two extra plates per cell for 30% more power. Our POWER HOUSE Hi-Torque Low Maintenance line features 5% to 8% more cold cranking power than our standard high output series and less maintenance is required because of advanced lead calcium technology instead of conventional lead antimony, so water loss due to gassing is reduced by 90%. By incorporating the latest in battery technology, each POWER HOUSE and Hi-Torque battery delivers the ultimate in value.

Note: All Batteries are shipped dry without acid and include instructions on how to fill the battery with acid. Terminal hardware and a vent tube is also included. See electric section for POWER HOUSE PLUS Maintenance ree Batteries.

Note: Battery warranty is based on a six month pro-rated policy. OUR POLICY WILL ONLY COVER THE BATTERY OR 6 ULL MONTHS ROM THE DEALER'S INVOICED PURCHASE DATE.

Not Shippable by Air
POWER HOUSE
Fits Sportster 1979/1996, XLCR 1977/1978, X Electric Start models 1973/Later, FXR 1982/Later, Softail 1984/1990
240 Cold Cranking Amps, 19 Standard Amp Hours
6 15/16 Long x 4 Wide x 6 1/8 Tall
Terminal Location: + on FLH, - on RH
JIS# YB16-B, Replaces HD# 65991-75C

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 31 1/2", Each, Harley 06-16 FX 07-16 FL

• Up to 80% lighter than lead acid batteries
• 5 times the life span of lead acid batteries
• 4 battery terminal mounts for custom cable mounting
• Can be mounted in any direction
• 2 year shelf life
• Lithium batteries DO NOT SULPHATE
• 3 year limited warranty
• Batteries include battery box insulation

Deltran Battery Tender
1.2 lb. Battery, 120 Cold Cranking Amps
4.21 Length x 2.2 Width x 3.35 Height
Fits Custom application where size matters

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 31 1/2", Each, Harley 06-16 FX 07-16 FL

• Up to 80% lighter than lead acid batteries
• 5 times the life span of lead acid batteries
• 4 battery terminal mounts for custom cable mounting
• Can be mounted in any direction
• 2 year shelf life
• Lithium batteries DO NOT SULPHATE
• 3 year limited warranty
• Batteries include battery box insulation

Deltran Battery Tender
1.76 lb. Battery, 240 Cold Cranking Amps
5.27 Length x 2.55 Width x 3.62 Height
Fits Sportster 2004/Later & VRSC V-Rod 2002/Later

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 31 1/2", Each, Harley 06-16 FX 07-16 FL

• Up to 80% lighter than lead acid batteries
• 5 times the life span of lead acid batteries
• 4 battery terminal mounts for custom cable mounting
• Can be mounted in any direction
• 2 year shelf life
• Lithium batteries DO NOT SULPHATE
• 3 year limited warranty
• Batteries include battery box insulation

Deltran Battery Tender
2.6 lb. Battery, 360 Cold Cranking Amps
6.49 Length x 3.38 Width x 5.11 Height
Fits FLT, FLHT, & FLHR 1980/1996

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 31 1/2", Each, Harley 06-16 FX 07-16 FL

• Up to 80% lighter than lead acid batteries
• 5 times the life span of lead acid batteries
• 4 battery terminal mounts for custom cable mounting
• Can be mounted in any direction
• 2 year shelf life
• Lithium batteries DO NOT SULPHATE
• 3 year limited warranty
• Batteries include battery box insulation

Deltran Battery Tender
3.75 lb. Battery, 480 Cold Cranking Amps
6.49 Length x 3.38 Width x 5.11 Height
Fits FLT, FLHT (including Road King & Road Glide) 1997/Later, Tri-Glide all models

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 32 15/16", Each, Harley 87-06 FX 87-06 FL 86 - 13 XL

Cadmium 2-brush generator screws.

XL 1957-1970

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 32 15/16", Each, Harley 87-06 FX 87-06 FL 86 - 13 XL

Allen type generator screw.

XL 1957-1970

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 32 15/16", Each, Harley 87-06 FX 87-06 FL 86 - 13 XL

Chrome generator screw kit

XL 1971-1985

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 32 15/16", Each, Harley 87-06 FX 87-06 FL 86 - 13 XL

Zinc generator screw kit

XL 1971-1985

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 32 15/16", Each, Harley 87-06 FX 87-06 FL 86 - 13 XL

• Maintenance free design eliminates the need to ever add water to the battery
• Sealed enclosure allows mounting the battery in any position (except upside-down)
• To help improve vibration resistance, the battery acid is absorbed between the plates with fine microfiber glass mats (AGM)
• Internal gas pressure is valve regulated to prevent any water loss (VRLA)
• AGM & VRLA combined with lead-calcium grid plates provide more cold cranking amps than lead acid type batteries with up to three times the life span
• Includes a sulfation retardant that dramatically reduces the battery killing plate sulfation that is commonly associated with conventional batteries
• Extremely slow rate of self-discharge when not in use, but must be slow charged at least every three months if not in service
• Includes cable mounting hardware
• * Includes mounting kit with terminal cover and plastic bumpers

Important Note: These batteries include a separate battery acid pack and must be used to fill the battery before use (except 10023 and 10049, these come pre-filled and charged). The metered acid pack delivers the precise amount in a safe and controlled manner. illing and charging instructions are included.

Note: Battery warranty is based on a six month pro-rated policy. SIX MONTH BATTERY WARRANTY STARTS WHENEVER THE DEALER ILLS THE BATTERY WITH ACID AND SLOW CHARGES IT TO A RANGE O 12.8 THROUGH 13.2 VOLTS. Please call your salesperson for details.

Not Shippable by Air
POWER HOUSE PLUS
* 310 Cold Cranking Amps, 18 Amp Hours
6 ⁷/₈ Long x 3 ⁷/₁₆ Wide x 6 ¹/₈ Tall
Fits FXR 1982/Later, X electric start 4 speed 1973/1986, Softail 1984/1990, Sportster 1979/1996, XLCR 1977/1978
Terminal Location: + on FLH, - on RH
Replaces HD# 66672-96
MG# YTX20H-BS

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 32 15/16", Each, Harley 87-06 FX 87-06 FL 86 - 13 XL

• Maintenance free design eliminates the need to ever add water to the battery
• Sealed enclosure allows mounting the battery in any position (except upside-down)
• To help improve vibration resistance, the battery acid is absorbed between the plates with fine microfiber glass mats (AGM)
• Internal gas pressure is valve regulated to prevent any water loss (VRLA)
• AGM & VRLA combined with lead-calcium grid plates provide more cold cranking amps than lead acid type batteries with up to three times the life span
• Includes a sulfation retardant that dramatically reduces the battery killing plate sulfation that is commonly associated with conventional batteries
• Extremely slow rate of self-discharge when not in use, but must be slow charged at least every three months if not in service
• Includes cable mounting hardware
• * Includes mounting kit with terminal cover and plastic bumpers

Important Note: These batteries include a separate battery acid pack and must be used to fill the battery before use (except 10023 and 10049, these come pre-filled and charged). The metered acid pack delivers the precise amount in a safe and controlled manner. illing and charging instructions are included.

Note: Battery warranty is based on a six month pro-rated policy. SIX MONTH BATTERY WARRANTY STARTS WHENEVER THE DEALER ILLS THE BATTERY WITH ACID AND SLOW CHARGES IT TO A RANGE O 12.8 THROUGH 13.2 VOLTS. Please call your salesperson for details.

Not Shippable by Air
POWER HOUSE PLUS
200 Cold Cranking Amps, 12 Amp Hours
6 Long x 3 ⁷/₁₆ Wide x 5 ³/₄ Tall
Fits Sportster 2004/Later
Terminal Location: - on FLH, + on RH
Replaces HD# 65958-04
MG# YTX14L-BS

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 32 15/16", Each, Harley 87-06 FX 87-06 FL 86 - 13 XL

• Maintenance free design eliminates the need to ever add water to the battery
• Sealed enclosure allows mounting the battery in any position (except upside-down)
• To help improve vibration resistance, the battery acid is absorbed between the plates with fine microfiber glass mats (AGM)
• Internal gas pressure is valve regulated to prevent any water loss (VRLA)
• AGM & VRLA combined with lead-calcium grid plates provide more cold cranking amps than lead acid type batteries with up to three times the life span
• Includes a sulfation retardant that dramatically reduces the battery killing plate sulfation that is commonly associated with conventional batteries
• Extremely slow rate of self-discharge when not in use, but must be slow charged at least every three months if not in service
• Includes cable mounting hardware
• * Includes mounting kit with terminal cover and plastic bumpers

Important Note: These batteries include a separate battery acid pack and must be used to fill the battery before use (except 10023 and 10049, these come pre-filled and charged). The metered acid pack delivers the precise amount in a safe and controlled manner. illing and charging instructions are included.

Note: Battery warranty is based on a six month pro-rated policy. SIX MONTH BATTERY WARRANTY STARTS WHENEVER THE DEALER ILLS THE BATTERY WITH ACID AND SLOW CHARGES IT TO A RANGE O 12.8 THROUGH 13.2 VOLTS. Please call your salesperson for details.

Not Shippable by Air
POWER HOUSE PLUS
200 Cold Cranking Amps, 12 Amp Hours
6 Long x 3 ⁷/₁₆ Wide x 5 ³/₄ Tall
Fits VRSC V-Rod 2002/Later
Terminal Location: + on FLH, - on RH
Replaces HD# 65948-00
MG# YTX14-BS

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 32 15/16", length 80", Harley 87-06 FX 87-06 FL 86 - 13 XL

• Recommended for high compression engines
• 1,661 individual 36 gauge tin coated copper strands strategically woven for maximum current flow
• High performance battery cables will increase starter performance by supplying maximum battery current to the starter motor
• Offer you a custom braided stainless appearance with an ultra-flexible translucent jacket that is oil & gas resistant and rated at 287° while providing excellent performance and show quality good looks
• Kits include one battery positive terminal to starter motor cable and one battery negative terminal to ground cable
• eatures:
  • Copper ends with corrosion resistant Zinc Plating
  • Electrolytic-Grade copper strands
  • The look of braided stainless steel
  • All cables have one ⁵/₁₆ I.D. end and one ¹/₄ I.D. end
  • Cable ends are crimped on and include waterproof heat shrink
  • 4 gauge for high performance
  All Balls
  13 Individual Cable

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 35 5/8", length 66 5/8", Each, travel 2 5/8", Harley 87-00 FX 87 - 94 XL

Add some flare to your ride. Replace your stock hardware on your switch housings with our V-Twin chrome allen screw set. This set can be used on your 1973-1981 XL or Big Twin models.

FL 1973-1981
FX 1973-1981
XL 1973-1981

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, clt adj location 35 5/8", length 69 13/16", Each, Harley 87-00 FX 87 - 94 XL

Chrome acorn generator screw

XL 1971-1984

DRAG SPECIALTIES Alternative Length Black Vinyl High Efficiency Clutch Cable, High-Efficiency, clt adj location 25 7/16", Each, Harley 08-16 FL

Autolite spark plugs, standard type.

OEM: 4123

XL 1980-1985

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, elbow 90, Harley 96-16 FX 96-16 FL 96 - 16 XL 02 - 16 VR
These Elite 1 ignition modules will give you the performance and flexibility for a wide range of applications. They offer a great advantage in tuneability and adjustability for stock performance, stock compression to high performance, high compression motors. It is as easy as 1 through 8 to dial in the correct advance curve and RPM limiter for just about any engine configuration up to 113ci. Just check out the features listed below and decide which one is best for your engine and go tear up some tires and clutches. See the wheel section for tires and the drive train section for clutches. When using single fire type coils, you will need the use of a tachometer adapter for correct RPM readout.

eatures Include:

• Fits in nose cone, no black box
• Single or dual fire
• Single or dual plug
• Eight selectable electronic advance curves
• RPM limiter and VOES diagnostic light
• RPM limiter 6000/unlimited in 250 increments
• Selectable levels of VOES 50%, 100% or none
• RI immunity allows solid wire and nonresistor spark plug use
• Accu-Ray TDC static timing light
• Use 2 to 3 OHMs of primary resistance coil
• Extended temperature and low voltage operation
• Automatic shutdown if ignition is left on with motor not running
• Includes instructions

Not legal for sale or use in California, or on any pollution controlled vehicles
Compu-ire
High performance up to 113ci
High compression up to 11:1
Kick or Electric start
Fits Big Twin 1970/1999 (except Twin Cam) & Sportster 1971/2003

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, elbow 90, Harley 96-16 FX 96-16 FL 96 - 16 XL 02 - 16 VR

• This complete mechanical advance kit uses state of the art bearing technology at the flyweight pivot points to provide the smooth, consistent and reliable ignition timing you demand
• Complete kit includes everything as shown to update your point style ignition system with top quality performance parts

Note: This kit can also be used to convert a Dual ire electronic ignition system to a point type mechanical advance ignition if used in conjunction with a 4.3 OHM through 5 OHM ignition coil.V-FACTOR
Fits Big Twin 1970/Early 1978 & Sportster 1971/Early 1978

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, elbow 90, Harley 96-16 FX 96-16 FL 96 - 16 XL 02 - 16 VR
High quality ignition point sets meet or exceed OEM specifications.V-FACTOR
Fits Big Twin 1948/1969, K Model & Sportster 1954/1970 without Magneto and all 45ci 1948/1973
Replaces HD# 30605-48A
(Imported)

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, elbow 90, Harley 96-16 FX 96-16 FL 96 - 16 XL 02 - 16 VR
High quality ignition point sets meet or exceed OEM specifications.V-FACTOR
Fits Big Twin 1970/Early 1978 & Sportster 1971/Early 1978
Replaces HD# 32661-70T

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, elbow 90, Harley 96-16 FX 96-16 FL 96 - 16 XL 02 - 16 VR
High quality ignition point sets meet or exceed OEM specifications.Standard Motor Products
Fits XLCH with Magneto 1958/1969 & all Morris Clockwise Rotating Magnetos
Replaces HD# 29533-55A

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, elbow 90, Harley 96-16 FX 96-16 FL 96 - 16 XL 02 - 16 VR
High quality ignition condensers meet or exceed OEM specifications.V-FACTOR
Fits all Points Type Ignition (except Magneto models)
Replaces HD# 32726-30A
(Imported)

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, elbow 90, Harley 96-16 FX 96-16 FL 96 - 16 XL 02 - 16 VR
High quality ignition condensers meet or exceed OEM specifications.Standard Motor Products
Fits XLCH 1958/1969 with Magneto and airbanks Morris, Joe Hunt and Morris Magnetos
Replaces HD# 29534-55A

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, elbow 90, Harley 96-16 FX 96-16 FL 96 - 16 XL 02 - 16 VR

• Definitely a must for any complete custom job
• Cover will appropriately dress your starter solenoid
• Includes mounting screws

V-FACTOR
Chrome Plated Cover
Fits Big Twin 1991/Later, Sportster 1200 models 1991/Later & 883 models 1995/Later
Replaces HD# 31688-90
(Imported)

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, elbow 90, Harley 96-16 FX 96-16 FL 96 - 16 XL 02 - 16 VR
This is a high quality reproduction of the OE Prestolite style starter motor.HARDWARE
Replacement set of brushes only with terminals
Fits most Big Twin & Sportster Late 1966/1982
Replaces HD# 31541-66

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, length 48", Harley 02-05 FL

• Designed to hold the regulator/rectifier plug tight against the stator plug preventing arcing and premature failure
• Made from die cast aluminum

V-FACTOR
Cast Aluminum Plug Retainer
Fits Big Twin 1970/1988 with right angle plug
(Imported)

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, Push-in, cruise ready, elbow 90, Harley 02-07 FL

• V-FACTOR regulators/rectifiers are available for mostHarley-Davidson^® models
• These high quality units have improved solid state circuitry and high performance components that guarantee superior performance and reliability
• All semi-conductors are USA made
• Connectors and terminals on 1997/Later applications are from Deutsch and Delphi
• See below for availability of finishes
• See additional images for plug types

V-FACTOR
Chrome Plated, 15 amps
Fits Big Twin 1970/1975 (requires 16306 or 16308 two bolt type mount)
Replaces HD# 74510-70A

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, Push-in, cruise ready, elbow 90, Harley 02-07 FL

• V-FACTOR regulators/rectifiers are available for mostHarley-Davidson^® models
• These high quality units have improved solid state circuitry and high performance components that guarantee superior performance and reliability
• All semi-conductors are USA made
• Connectors and terminals on 1997/Later applications are from Deutsch and Delphi
• See below for availability of finishes
• See additional images for plug types

V-FACTOR
Chrome Plated, 19 amps
Fits Sportster Late 1984/1990
Replaces HD# 74523-84A

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, Push-in, elbow 90, Harley 02-07 FL

• Improved circuitry combined with high performance components provide superior operation and reliability
• Covered by the manufacturer's limited replacement warranty
• See additional images for plug type

Accel
Chrome Plated OE style 12 volt, 38 Amp Regulator/Rectifier for Alternator models
Fits Softail 2001/2006
Replaces HD# 74610-01

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, Push-in, elbow 90, Harley 96-16 FX 96-16 FL 96 - 16 XL 02 - 16 VR

• Contructed with quality materials ensuring long life
• Equipped with 23 oz. Spring pressure to eliminate points bounce at high engine RPM

Accel
Fits Big Twin 1970/Early 1978 & Sportster 1971/Early 1978
Replaces HD# 32661-70

DRAG SPECIALTIES Alternative Length Black Vinyl Idle Cable, Push-in, elbow 90, Harley 96-16 FX 96-16 FL 96 - 16 XL 02 - 16 VR
V-FACTOR
Heavy Duty Black Rotor
Fits Big Twin 1981/1998 with 22-32 Amp charging system
Replaces HD# 29957-81B & 29957-85A
(Imported)