All

Jims shaft nuts now give the ultimate in flywheel holding power. The mating face of each nut has been ground to a 32 surface finish and held square to threads within .0005". This in turn will pull the shafts straight into the flywheels and simplify flywheel truing. We didn't stop there! Each nut is machined on state of the art CNC lathes, and heat treated to make these nuts the toughest and best available on the market.

"T" Type Pinion Gear Shaft Key
Fits Big Twin Evolution 1990/1999, K Model & Sportster 1988/1999
Package of 10
Replaces HD# 11219

BDL 1 rear replacement belt is 133 tooth. 2007-2011 FLST

BDL 1 rear replacement belt is 137 tooth. 2007-2008 FLT

Fork stem die holder is for use with a 1 x 24 TPI fork stem die tool. 1948-1985 FL

Riser set is for use with 1 diameter handlebars. Set features a custom short style with black aluminum billet and a contrast cut. Custom applications

Riser set is for use with 1 diameter handlebars. Set features a custom short style and is constructed with solid brass billet with a contrast cut. Set is cast solid. May have pits and marks from the hand casting process. Custom applications

1 handlebar sleeve constructed of raw steel slides over the original bar end to eliminate stock internal throttle or spark assemblies 1949-1959 FL

1 linkert carburetor rebuild kit includes hardware and all necessary parts to fit linkert carburetors. Kit includes the overhaul kit throttle shaft and its corresponding disc. Additional installation hardware includes: screws bushings throttle shaft spring main nozzle spring float bowl gasket washers intake gaskets needle valve gasket carburetor cork float float pivot pin choke detent ball with spring float needle and seat. 1937-1957 G

Linkert 1 throttle disc is #12 type to fit 1 Linkert carburetors. 1936-1956 G

Shock set will lower by 1 features chrome springs and body caps. Lower kickstands are also available separately. The distance between eye to eye measures 11-3/4 . Warning: Installing a lowering kit or shorter shocks will decrease initial ground clearance. the motorcycle will be lower to the ground and care should be taken to avoid bottoming especially over bumps or in turns. 2006-2010 XL 883 2009-UP XL 1200C

Brass sand riser set is for use with 7/8 -1 handlebars. Set features a smooth casting polished finish. Custom application

Chrome 1 handlebar Super Bar style features a dimple and knurls. 1982-1984 FL 1982-1984 FX 1982-UP XL 1986-2017 FLST 1984-2017 FXST 1982-1994 FXR 1991-2017 FXD 1982-2007 FLT

This fork neck cup set is used when installing a Big Twin or late Sportster 1 neck fork assembly on early Sportster models. Allows installation of Spring Forks with a 1 neck stem. Includes dust cover races installed and bearings Remove your existing cups and install these cups into your frame neck and you are ready to install any 1 neck stem fork assembly. *NOTE: Order related spacers and nuts separately. **NOTE: Spacers can be installed on the underside of the neck for added height. 1957-1977 XL 1937-1952 W 1937-1957 G

1 x24 zinc plated spring fork stem hex nut is a duplication of original part. Spring fork hex nut features centering shoulder. 1936-1940 EL 1941-1948 FL 1937-1948 UL

1" Lowered Kickstand Dresser Models 2007/Later* Use On Lowered Bikes

• When you lower your Dresser model, you have to use a shorter kick stand to allow correct lean angle when your bike is parked
• Handcrafted in the USA, TIG welded and hand polished to accept smooth show quality chrome plating
• Mounts on OE bracket and utilizes the OE kick stand spring
• Will also fit years back to 1984, but lean angles may vary

Pingel
Chrome Plated Kick Stand
Length: 1 Lowered ront, 1 Lowered Rear
Fits Dreser models 2007/Later

Oversized Linkert carburetor 1-1/16 venturi is precision machined aluminum and made to exact tolerances for perfect fit and performance. Replacement venturi for M2 M5 M21 M41 M51 M52 M55 M58 M64 M65 M84 and M97 carburetors. 0-Replacement application 1937-1942 WL 1936-1954 G

This 1-1/16 linkert carburetor venturi is precision machined to exact tolerances constructed of aluminum. This venturi is for M2 M5 M21 M41 M51 M52 M55 M58 M64 M65 M84 M88 & M97. 1941-1952 W

Carlisle Panther 1-1/2 rear belt has 133 tooth. 1991-1999 FXD

1-1/2 chrome plated steel concho. Sold as a pack of 50. 0-All models

Overhaul kit for 1-1/2 carburetors includes throttle shaft brass float needle and seat float bushings springs float pin gasket carburetor bowl large nut with stud lock washer luck nut and copper filled seal washer. For M74 models. Threads on this needle and seat assembly is 7/16 x 27. *NOTE: For the float arm installation the center prong of the float arm should have .003 of clearance in order for the arm and needle to move freely. 1941-1965 FL 1941-1952 EL

Top it off in style and add a custom touch to your bike with this black 1-1/2 shorty riser set. Risers have a 1/2 -13 thread for 1 handlebars. Custom application

If you like the feel of your handlebars and just want to position them differently consider this short riser set for use with a full 1-1/4 diameter bars at riser mount section Risers will accept full 1-1/4 bars only these are bars in which the clamping area is 1-1/4 in diameter. 2007-UP FXST 1-1/4 handlebars"

Oversized Linkert carburetor 1-1/8 venturi is precision machined aluminum and made to exact tolerances for perfect fit and performance. Replacement venturi for M61B M61 M36A M36 M35 M35T M35TP caburetors. 0-Replacement application

Riser stems are chrome plated steel and have a 3/4 -16 UNF thread to screw into spring fork rear legs. The spring fork rear legs must be threaded to accept risers. Use tops and bushings from existing Flanders risers. Installation of these riser stems requires tapping of the rear leg tube to 3/4 x 16 for mounting. Requires the use of a 3/4 -16 UNF tap. 1941-1948 FL 1936-1952 W 1936-1957 G 1936-1948 EL 1937-1948 U

This aluminum 1-1/8 linkert carburetor venturi is precision machined to exact tolerences. Fits M-51L and M-41L carburetors. 0-Replacement application for M41L and M51L carburetor. 1941-1952 W 1941-1948 U

Pipe set measure 9-1/2 long and features a fiber glass fitting to fit straight or drag pipes with an outer diameter of 1-3/4 . Custom Application

Speed freak handlebar riser set features a gloss black finish and is 1-3/4 tall for 1 handlebars. Uses 1/2 -13 mounting bolts. *NOTE: Bolts not included. Custom application for 1 handlebars"

Baffle pipe set fits inside drag pipes. 1-3/4 denotes the size of the pipe into which the baffle fit. Baffle is 8 and the baffle outer diameter is 1.61 . Set comes in fiberglass packing. Custom application for drag pipes