All

Outer bearing race for Joe Hunt Morris Fairbanks Morse magnetos. Race for points plate bearings OEM # 29562-55 for rotor cam end. 1957-1970 XL

Magneto red button kill switch kit includes bushings and stud for installation. Points and condenser for magneto also included. Fairbanks-Morse factory aluminum name tag included but not installed. 1957-1970 XL

Magneto rotor collar includes bearing and is for use with XR models. *NOTE: Must order inner magneto mount plate separately. 1957-1970 XR

Rotor grease retainer washer. 1958-1965 XLCH

This rotor shaft end seal is molded rubber. 1958-1965 XLCH

Rotor shaft end snap ring. 1958-1962 XLCH

Rotor shaft end spring clip. 1958-1965 XLCH

Rotor shaft end washer. 1958-1965 XLCH

Screw set is used for solid mounting with cast base of original magnetos. Use 1/4 x 20 UNC x 7/8 serrated flange head screws (MSC 83242107) with 1/4 x 20 UNC serrated flange nuts (MSC 67483362). 1958-1964 XLCH

Magneto shaft features snap ring groove and hex drive. 1936-1973 G 1936-1952 W 1937-1948 U

The magneto shaft assembly has advance adjustment and includes four mount screws to attach to the base of the magneto head. The mount screws for attaching the flange to the case are not included. Use 1/4 -20UNC or 1/4 -24 screws as required. Order magneto top and body separately. The hex shaft that goes into the magneto should be 3/8 . *NOTE: Must lubricate before assembly. 1941-1969 FL 1936-1952 EL

Magneto tachometer kit includes mount bracket to mount to XL handlebar mount. Tachometer is OEM HD manufactured in Italy. 1957-1970 XL

Magneto tachometer plug kit includes plug pin cottter pin and o-ring. 1962-1969 XL

Magneto vent cap set includes two of each cups screws and nuts. Two pieces as required in Fairbanks Burkhardt Joe Hunt and Morris. 1958-1965 XLCH

Made of 8620 steel with .62 heat treated penetration and is a 3-hole type. 1957-1980 XL

Main dash coil wiring harness assembly runs from the dash panel to the OEM type terminal box mounted behind the coil or dual point coils. *NOTE: Made from 16 gauge cotton braided over vinyl wire with machine crimped and insulated #6 of the red and green wires and crimped #10 flag terminals on the other wire ends. 1948-1969 FL

This 45 main drive gear seal installer. 1929-1973 G

Main drive gear seal kit includes a case race nut lock tab seal o-ring and cork. 1941-1976 FL

Main drive gear spacer kit for 4 speed models includes nut seal kit and collar. 1941-1976 FL 1937-1952 EL

Main nozzle discharge tube with lower plug is for L series carburetors. 0-All application for L" series carburetor"

Main wiring harness features plastic covered wires. Main wiring harness includes high tension wires only. Order handlebar tail lamp and turn signal wires separately. 1975-1976 XLH Electric start XL models

Iron Cross ignition system cover is 5-hole style with chrome finish. Iron cross is raised design. 1999-UP FXST 1999-UP FLST 1999-2017 FXD 1999-UP FLT

Maltese LED tail lamp with red lens and chromed housing. *NOTE: For show or decorative use only not D.O.T. approved. 0-All models

This kit allows precise adjustment of the primary chain and creates less drag and loss of power resulting from the stock spring loaded assembly. This new manual primary chain tension adjuster kit is ideal for bikes equipped with big displacement high performance engines. Permits manual selection of primary chain tension and is a direct replacement for the original equipment automatic version. The anodized billet aluminum adjuster allows you to fine tune and lock settings. The manual adjustment locks the chain tension in place to prevent free play during severe shifting. Kit includ
18-8329" Chrome early clutch rod end is for foot clutches. *NOTE: Threads are 10/32 N.F. 2007-2016 FL 2006-2017 FXD 2007-2017 FXST 2007-2017 FLST 2009-2016 FLHXXX

Replacement red lens standard type lens set. 0-Replacement application part for tour lamps.

Master cylinder front gasket. 2015-2017 FXST 2015-UP FL

Master cylinder rebuild kit includes top gasket and internal components. Custom application

Matchless motorcycle patches can be either ironed or sewn on . NOTE: When using an electric iron to apply the patches to clothing NEVER use steam. Patch may be sewn on after being attached with it's adhesive. Sold as a pair. 0-All

3-slot wide style hand lever set features a matte black finish. 2015-2017 FXSB 2015-2017 FLSTN 2015-2017 FLSTF 2015-2017 FLSTC

3-slot wide hand levers are formed to make them easier and more comfortable to use for use on Touring models featuring a matte black finish. Set of two. 2014-2016 FLT

Smooth wide style hand lever set features a matte black finish. 2015-2017 FXSB 2015-2017 FLSTN 2015-2017 FLSTF 2015-2017 FLSTC

McCulloch engine patches can easily be ironed or sewn on. Sold as a pair. NOTE: When using an electric iron to apply the patches to clothing NEVER use steam. Patch may be sewn on after being attached with it's adhesive. 0-All

1-3/4 drag pipe set with a 2 full coverage form fitted heatshield set both featuring a chrome finish. The heatshield runs from the exhaust port to the end of the pipe and has a slash cut built in. Form fitted heatshield is longer than inner pipe for a one piece seamless look. *NOTE: Mounts to stock bracket. 2007-2017 FXST

1-3/4 drag pipe set with a 2 full coverage form fitted heatshield set both featuring a chrome finish. The heatshield runs from the exhaust port to the end of the pipe and has a slash cut built in. Form fitted heatshield is longer than inner pipe for a one piece seamless look. *NOTE: Requires the separate purchase of the mounting bracket for installation. 1971-1984 FX 1971-1984 FXE