All

Kit includes black solo seat chrome 3 hair pin springs cross bar with spring dowels and 1 clamp set to mount to fender cross bar. Custom application

Raw steel frame forging hallmark plate is an accurate investment for reconstruction and restoration of 1936-1957 rigid frames includes various forging logos and numbers. Investment cast steel in one sheet cut numbers out as desired. Frame may be milled or ground down to accept numbers and forging marks. The numbers when cut from the plate may be ground down for specific application. *NOTE: Must be welded in place. *NOTE: The plate is 2.5 - 2.8mm thick. 1936-1957 Custom Application

Rigid hardtail frame raw steel rear section is 1957 style replica construction with components featuring the factory details of the period. The rear transmission mounts are 2 from the bottom cross beam to the top of the plate. May be used to repair 1948-1957 FL rigid frames or as a hardtail conversion on 1958-1984 FL frames. This rigid hardtail rear frame section includes: rear engine mount center post front transmission mount transmission cross strap spools rear axle plates fender cross tube tool box mount oil tank mount lower fender mount footboard tabs as a welded a
51-0825" Black standard type frame swingarm is for 4-speed chain drive models. Swingarm shock mounts are welded 10.67 back front center of swingarm bolt. Bearings and races are not included. For use with banana style caliper only. Can be used on 1973-Early 1978 models but will raise seat height. Tabs for chain guard are 10-1/2 apart center to center. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 1948-1984 FL

Rigid Panhead book set is for Panhead Rigid frame models. Includes 1 each: Parts Service and Shop Dope books. **NOTE: Product May Not Be Returned. 1948-1957 FL

Rigid rear axle features a parkerized finish. 1936-1952 EL 1941-1957 FL

Rear fender brace set is the narrow brace profile style with the brackets riveted to the straps. The stay features a slot on one end and two rivet holes on the other end. Rivets and bolts are not included. Set features a raw finish. Braces are 7/8 wide. 1949-1957 FL

Brackets are 7/8 wide with slots at the end featuring a raw steel construction. Set of two. 1947-1955 FL

Brackets are 3/4 wide with slots at the end with raw steel construction. Stay features slots on one end and two rivet holes on the other end. Set of two. Order mount bolt kit separately. 1956-1957 FL

Raw rigid rear fender tab set is the OE type to replace right and left sides on fender brace. Must be riveted in place. *NOTE: Rivets not included. 1936-1952 EL 1941-1957 FL

Chrome shot gun drag pipes are for a rigid frame with Shovelhead engine. Front pipe is an outside type. Order bracket separately. *NOTE: The front pipe is 1 piece and the rear pipe is 1 piece. **CAUTION: These exhaust products are not legal for sale or use in California on pollution controlled vehicles. These products are intended for non-highway only. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 1966-1984 FL

This adapter kit will allow 10° angular mounting of the risers by use of eccentric bushings. For use with 1/2 mount bolts. Custom application

This adapter kit will allow 5° angular mounting of the risers by use of eccentric bushings. Features a chrome finish. Use with 1/2 mount bolts. Custom application

RL clutch hub lock tab features a raw finish. 1933-1940 RL

Chrome 1-1/4 handlebar features throttle by wire right side notches and has holes with a copper wire inside for pulling thru internal wiring. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs.

2008-2014 FLTR

Easy to install Road Glide windshield trim adds a chrome accent to the center of the fairing machined from billet aluminum. The center trim will fit with original side trim. Includes mounting hardware. *NOTE: Does not fit CVO models with stock side trim. CVO models will require the separate purchase of the Road Glide Windshield Side Trim Kit. 2015-UP FLT

Easy to install Road Glide windshield trim adds a chrome accent to the sides of the fairing machined from billet aluminum. Includes left and right side trim and mounting hardware. *NOTE: Designed to be used with the Road Glide Windshield Center Trim Kit. 2015-UP FLHR

Rocker arm ball stud comes as 4 pieces. 1937-1940 EL 1941-1947 FL

Nuts and seals for rocker arm cover oil line fittings. 1966-1984 FL 1971-1984 FX 1957-1984 XL 1979-1984 FLT 1982-1984 FXR

Cadmium rocker arm cover hex head screw kit is the reproduction of screws used on 1938-1947 Knucklehead models. This is a 34 piece kit. 1941-1947 FL 1939-1940 EL

Chrome rocker arm cover hex head screw kit is the reproduction of screws used on 1938-1947 Knucklehead models. This is a 34 piece kit. 1941-1947 FL 1939-1940 EL

Rocker arm cover fillister head slotted parkerized screw kit for 1938 61 overhead valve models is the reproduction of screws used on 1938-1947 Knucklehead models. This is a 34 piece kit. 1938-1938 EL

Parkerized rocker arm cover hex head screw kit is the reproduction of screws used on 1938-1947 Knucklehead models. This is a 34 piece kit. 1941-1947 FL 1939-1940 EL

Knucklehead rocker arm set. Sold as a set of 4. 1937-1940 EL 1941-1947 FL

Rocker arm shaft adjusting tool for use on Knucklehead models. 1936-1939 E 1936-1939 EL 1936-1939 FL

This rocker box breather upgrade includes breather tubes only. Set of two. 1992-1998 FXST 1992-1998 FLT 1992-1994 FXR 1992-1998 FXD

Chrome d-ring set for rocker boxes on XL models. 1986-1990 XL

Rocker box cover kit includes two top chrome finish die-cast covers and two lower rocker box housings with gaskets and hardware for two heads. On 2007-Up models the D-ring is part of the lower box housing. 2007-UP XL

Rocker box cover set with black finish. Four piece set for two cylinders. 2004-2006 XL

Rocker box cover set with black finish. Four piece set for two cylinders. 2007-UP XL

Chrome rocker box cover set is a 6 piece kit. Covers have a smooth finish and include gaskets for both heads. 2004-2006 XL

Chrome rocker box cover set is a 6 piece kit. Covers have a smooth finish and includes gasket for both heads. 2007-UP XLS

Dress up your XL with our V-Twin Mfg. matte black heat proof finish rocker box dress cover set that fits over your stock rocker boxes and mount using the chrome allen screws included. 1986-UP XL

Gasket kit for rocker boxes and push rod covers is a complet e 26 piece set. Kit includes eight fiber washers two silicone rocker cover inner gaskets two silicone rocker cover lower gaskets two silicone breather seals two rubber coated steel rocker box gaskets four viton pushrod cover upper gaskets four NBR o-rings and two non-asbestos tappet cover gaskets. 2007-UP XL