All

Cam & Gear Seat N8 Grind Spt Evo 883 1100 1200Cc 00/L* Vlv/Sprg Clearance M# 298190
A camshaft upgrade is the most logical step after air filter, exhaust, carburetor, and ignition system improvements have been made. It will improve mid and upper-end power. All camshafts listed are ground with stock size base circle and can be used with stock push rods. Instructions included.

Cam Specifications - with stock 1.43:1 rocker arm ratio

Cam Grind	Valve Timing	Duration @ .053	Duration @ .020	Valve Lift	Overlap @ .053	Lobe Centerline	Lobe Separation Angle	TDC Lift at Valve
Q stock (76/85)	10/32 35/07

Cam & Gear Set N2 Grind Spt Evo 883,1100 & 1200,91/99 Bolt In Andrews 298125
A camshaft upgrade is the most logical step after air filter, exhaust, carburetor, and ignition system improvements have been made. It will improve mid and upper-end power. All camshafts listed are ground with stock size base circle and can be used with stock push rods. Instructions included.

Cam Specifications - with stock 1.43:1 rocker arm ratio

Cam Grind	Valve Timing	Duration @ .053	Duration @ .020	Valve Lift	Overlap @ .053	Lobe Centerline	Lobe Separation Angle	TDC Lift at Valve
Q stock (76/85)	10/32 35/07

Cam & Gear Set N4 Grind Spt Evo 883 1100 1200Cc 00/L* Vlv/Sprg Clearance M# 298150
A camshaft upgrade is the most logical step after air filter, exhaust, carburetor, and ignition system improvements have been made. It will improve mid and upper-end power. All camshafts listed are ground with stock size base circle and can be used with stock push rods. Instructions included.

Cam Specifications - with stock 1.43:1 rocker arm ratio

Cam Grind	Valve Timing	Duration @ .053	Duration @ .020	Valve Lift	Overlap @ .053	Lobe Centerline	Lobe Separation Angle	TDC Lift at Valve
Q stock (76/85)	10/32 35/07

Cam & Gear Set Y Grind Ih Spt 57/70 Mid/Upper Range Power Bolt In Andrews 214075
A camshaft upgrade is the most logical step after air filter, exhaust, carburetor, and ignition system improvements have been made. It will improve mid and upper-end power. All camshafts listed are ground with stock size base circle and can be used with stock push rods. Instructions included.

Cam Specifications - with stock 1.43:1 rocker arm ratio

Cam Grind	Valve Timing	Duration @ .053	Duration @ .020	Valve Lift	Overlap @ .053	Lobe Centerline	Lobe Separation Angle	TDC Lift at Valve
Q stock (76/85)	10/32 35/07

Cam & Gear Set Y Grind Ih Spt 71/80 Mid/Upper Range Power Bolt In Andrews 214080
A camshaft upgrade is the most logical step after air filter, exhaust, carburetor, and ignition system improvements have been made. It will improve mid and upper-end power. All camshafts listed are ground with stock size base circle and can be used with stock push rods. Instructions included.

Cam Specifications - with stock 1.43:1 rocker arm ratio

Cam Grind	Valve Timing	Duration @ .053	Duration @ .020	Valve Lift	Overlap @ .053	Lobe Centerline	Lobe Separation Angle	TDC Lift at Valve
Q stock (76/85)	10/32 35/07

Cam Assembly Tool Twin Cam 07/L* Dyna 06/L* Jims 990

• Due to the radical new design of the Twin Cam, specialized tools are required to properly perform engine repair without damage
• All Jims tools are manufactured from top quality material and designed for years of trouble free service
• All tools include instructions

Jims
Cam Assembly Tool
Use this tool to hold both cams in an upright position while lowering the cam support plate over both guides and cam journal guides. Tool has been manufactured from a non-marring material, that will not damage any of the cam's surfaces. Use on all Twin Cam 2007/Later & Dyna 2006/Later

This 4 piece cam ball bearing set is for use on WR type conversions on 45 models. Cam center shaft must be turned down to accept ball bearings. *NOTE: If the inner and outer cam bushings are to be fitted with ball bearings 2 sets are required. 0-All WR type 45 models"

Cam Bearing & Gasket Kit Tc 99/06 Except 06 Dyna, Inner And Outer Bearings 288901

• Andrews
• These bolt-in type cams are designed for 88ci Twin Cam engines with stock compression using hydraulic lifters
• They are compatible with carbureted or fuel injected models. Note: EI models will require re-calibration of the ECU
• Reduced maintenance (no plastic chain guides or tension shoes to wear and contaminate your engine oil or clog oil passages)
• Cam timing remains constant. All drive and cam gears utilize a light press fit (gear lash) thus eliminating any chain stretch
• Bearing loads are reduced. No spring loaded chain tensioners are used (which can rob up to 4 horsepower)
• Critical sprocket alignment is unnecessary
• Can be used with the OEM non-adjustable pushrods, but we suggest using our adjustable pushrods found in the Engine Section to ease installation and eliminate the need to remove the fuel tank and rocker covers
• See General Merchandise Section for the required installation tools
• Includes instructions

Gasket & Bearing Kit by Andrews Products
Required for installation of 26G & 37G Grind CamsCam Specifications
with stock 1.625:1 rocker arm ratio

Cam Grind

Cam Bearing And Gasket Kit Twin Cam 2007/Later* Gasket And Inner Bearings

• Includes gasket and bearings for Andrews Performance Cams Andrews
  Cam Installation Kit

Cam Bearing Cam Case Big Twin 1958/2006 (Ex Tc) Rpls Hd #9058 Torrington #B138
Cam Needle Bearing
Fits Big Twin 1958/Later (except Twin Cam)
Replaces HD# 9058, Torrington B138

This Sifton cam bearing puller tool removes the inner cam bearing Torrington type without splitting cases while preventing rollers from coming out during the removal. Tool is designed for hand wrench use. Power driving with an air wrench or too much interference will break the stud. 1958-1984 FL 1971-1984 FX 1986-1998 FLST 1984-1998 FXST 1982-1994 FXR 1979-1998 FLT 1991-1998 FXD

Cam bearing puller tool removes the inner cam needle bearing #9057 without splitting the cases while preventing the rollers from coming out during removal. For use with bearing as listed. *NOTE: The shaft diameter before the flare measures 0.672 . 1957-1990 XL

Cam bearing remover tool allows the removal of needle bearings while keeping the needles from falling into the engine. For use with bearing as listed. *NOTE: The shaft diameter before the flare measures 0.974 . 2006-2017 FXD 2007-2017 FXST 2007-2016 FLT 2007-2017 FLST

Cam Bearing Remover Twin Cam 07/L* Dyna 06/L* Jims 993

• Due to the radical new design of the Twin Cam, specialized tools are required to properly perform engine repair without damage
• All Jims tools are manufactured from top quality material and designed for years of trouble free service
• All tools include instructions

Jims
Inner Cam Bearing Remover
Fits Twin Cam 2007/Later & Dyna 2006/Later
Blind hole puller will easily remove the crankcase needle bearing that supports the camshafts. The unique design prevents the pin rollers from accidentally falling into the crankcase that is known to happen when using inferior pullers

Cam Bearing Tool Collar Only For All Twin Cams Jims 1278-3

• Due to the radical new design of the Twin Cam, specialized tools are required to properly perform engine repair without damage
• All Jims tools are manufactured from top quality material and designed for years of trouble free service
• All tools include instructions

Jims
Cam Bearing Installation Tool
Collar Only fits all Twin Cams
Tool will install the two inner cam needle bearings into the crankcase. It perfectly aligns to the shaft bores for a precision press fit

Cam Brng Installation Tool Bt 58/L*(Ex Tc88) Sets Depth Perfect Alignment Jims .2188
This tool easily installs the bearing to the proper depth and alignment without damaging the bearing. Jims
Fits all Big Twin 1958/Later (except Twin Cam)

Cam Bushing Line Reamer Bt 70/L*(Ex Tc88) Gear Cvr Cam Bushing......Jims .1023-70

• Used to line ream and finish fit gear cover cam bushing
• This tool pilots off of the cam bearing for a true centerline.
• A must have tool to do a professional job

Jims
Fits Big Twin 1970/Later (except Twin Cam)

2019 New Production cam case pump 5-tooth drive gear features a 1.8 outer diameter 1939-1940 EL 1941-1953 FL

Cam Chain Guide Twin Cam 99/06 Except 06 Dyna Rpls Hd 39965-99
V-FACTOR
Cam Chain Guide
Fits Twin Cam 1999/2006 (except 2006 Dyna)
Replaces HD# 39965-99
(Imported)

Cam Chain Tensioner Pad Kit Twin Cam 1999/2006

• Chain tensioner pads are an item overlooked and when they fail, major issues can occur
• These pads work on the inner and outer tenioners and are made from a high performance polymide stanyl that surpasses the OEM material
• Sold as a kit with one pad and one pin

Cam Chain Tensioner Pad Kit
Fits Twin Cam 1999/2006

Cam Chain Tensioner Pad Tool Uw Part #66011 Pad

• Installing the pad kit is simple when using our pad installation tool
• The tool easily removes the old tensioner pin and allows for the installation of new pad and pin

Installation Tool
or use with our 66011 Cam Chain Tensioner Pad Kit

Cam Change Gasket & O-Ring Kit All Tc 88 1999/Later* Rpls Hd 17045-99 Mfg# C9664

• Cometic
• Includes all necessary Gaskets and O rings to perform a cam change
• The cam cover gasket is made from an aluminum base sheet covered with a chemically blown compound of foam-like synthetic rubber on both sides
• The rocker cover gaskets are made from an embossed stainless spring steel that has been coated on both sides with a nitrile bunadine rubber

Fits all Twin Cam 88 1999/Later
Replaces HD# 17045-99A

Panhead cam chest kit includes a natural finish cam cover and all internal parts. Assembly features a keyway slot. NOTE: Check the pinion and cam gears tolerance during assembly. 1954-1962 FL

This standard size sifton cam chest breather valve is constructed of precision ground steel with screen installed. Order thrust washers separately. *NOTE: 28.53mm outer diameter range 28.53 - 28.54mm. 1948-1977 FL 1971-1977 FX

Circuit breaker stud kit includes the cam chest circuit breaker shaft two bushings and a stud screw. 1959-1969 FL

Circuit breaker stud left handed screw. 1959-1969 FL

Cam chest idler gear stud kit. *NOTE: Does not include bushing. 1936-1952 EL 1941-1969 FL

Idler gear stud kit includes stud bushing and retaining ring. 1936-1952 EL 1941-1969 FL

Sifton kit includes idle shaft and one bushing. 1941-1969 FL