All

Beck sealed beam 6 volt bulb has a 50/40 watt output. Bulb is three prong style. 1949-1959 FL

Chrome 7 diameter air cleaner cover is for J-slot backing plates used on Linkert carburetors. The cover features a detailed 1940 World's Fair round embossed logo. 1941-1965 FL 1941-1952 W 1941-1955 G

Black 1 handlebar Z style feature early chopper styling with indents for external wiring. 1982-1984 FL 1982-1984 FX 1982-UP XL 1986-2017 FLST 1984-2017 FXST 1982-1994 FXR 1991-2017 FXD 1982-2007 FLT

Flat Rear Fender 7" Wide For Wide Tire Rigid Frame & Custom Use

• Designed with strength in mind, these one-piece HARDBODY rear fenders are cold rolled from 14 gauge steel
• They measure a full 48 in circumference and can be cut to your desired length
• enders are not drilled or relieved for the chain or drive belt
• See the frame and body section for fender supports

Raw Steel 7" wide flat fender
Fits Big Twin & Sportster Rigid frames

Vintage 1 diameter handlebar with a 7-1/2 rise is chrome plated with holes for internal wiring and notched for throttle by wire applications. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 1982-1984 FL 1982-1984 FX 1982-UP XL 1984-2017 FXST 1986-2017 FLST

Chrome plated vintage 1 handlebar has a 7-1/2 rise and holes for internal wiring and notched for throttle by wire applications. 1982-1984 FL 1984-2017 FXSTS

1909-1915 F 1930-1936 VL 1930-1936 RL 1937-1948 UL 1917-1926 JD

Clutch cable is black vinyl and is +10 overstock at 72.69 . 1987-1999 FXST 1987-1999 FLST 1987-1999 FLT

Clutch cable is black vinyl and is +4 overstock at 72.69 . 1995-1999 FXD 1993-2005 FXDL 1996-2005 FXDWG 1992-2005 FXDB

Clutch cable is black vinyl and is +4 overstock at 72.8 . 2006-2017 FXDWG

S&S forged .060 piston set for stroker flywheels. S&S stroker forged .060 piston set is machined to fit both 4-3/4 & 4-5/8 stroker flywheels. Piston set includes rings wrist pins and retainers. When used with 4-3/4 stroke compression will be 8.25:1 with 4-3/4 stroke compression will be 9:1. **Note: Remember that an 80 3-1/2 standard bore equals 3-7/16 +.060 bore size. **Note:Run Engine at moderate speeds for at least 500 miles avoiding excessive running in lower gears in order to properly break-in new pistons and rings. 1941-1977 FL 1971-1977 FX

S&S forged piston set 3-7/16 bore is standard size. Set includes rings wrist pins and retainers. Machined to fit 4-3/4 or 4-5/8 stroker flywheels. **Note:Run engine at moderate speeds for at least 500 miles avoiding excessive running in lower gears in order to properly break-in new pistons and rings. 1941-1977 FL 1971-1977 FX

Replica front cylinder has an OE style casting number code. Cylinder is bored and honed to 3.438 inner diameter. 1948-1952 FLH

Replica rear cylinder has an OE style casting number code. Cylinder is bored and honed to 3.438 inner diameter. 1948-1952 FLH

74 Link Primary chain is 428 x 74. 1994-2006 FLT

Clutch cable in braided stainless steel is +12 over stock length to fit stock Big Twin models. Stainless steel clutch cable is constructed with Supra stainless steel braid which is tightly woven for a bright quality consistent finish. The clear coat is UV resistant heat bonded and non-yellowing grade for a long service life. The cable has a casing length 75.25 and an overall length of 79.50 . 1987-2006 FLT 1987-2006 FLST 1987-2006 FXST 1987-2006 FXSTC

Zinc plated 750 XL lock nut tool is for use with 750 XL rear hub lock nut set. 1970-1980 XL

750 XL hub lock nut set features a zinc finish and a thread size of 2.031. 1941-1952 WR 1957-1972 XL

51 tooth XL rear sprocket with 5 holes is for 520 chain to fit splined carrier. Sprocket features an alloy construction and a natural aluminum finish. 1972-1984 XL

750 XL rear wheel hub is made with alloy construction and features a natural finish. For 40 spoke hole rims. Features knock off threaded end for quick change rear sprockets. Includes 11/16 bearings to fit stock sportster axles that are pre 1979 models and one lock nut. Accepts 11/16 axle shaft and 6-8 gauge spokes. Accepts 38 tooth splined rear sprocket 49 tooth splined engine sprocket and 51 tooth splined engine sprocket. *NOTE: Alloy splined adapter is for sprocket and disc mounting. Disc mounting is a very close fit and should be tapped with rubber mallet - being careful no
45-0108" Chrome front spool wheel hub includes 5/8 inner diameter bearings and accepts 40 9 gauge spokes. 1957-1984 XL

Clutch cable is black vinyl and is +8 overstock at 76.69 . 1995-1999 FXD 1993-2005 FXDL 1993-2005 FXDWG 1992-2005 FXDB

Clutch Cable is black vinyl and is +16 overstock at 78.69 . 1987-1999 FXST 1987-1999 FLST 1987-1999 FLT

Clutch cable in braided stainless steel is +16 over stock length to fit stock Big Twin models. Stainless steel clutch cable is constructed with the Supra stainless steel braid which is tightly woven for a bright quality consistent finish. The clear coat is UV resistant heat bonding non-yellowing grade for a long service life. The cable has a casing length 78.69 and overall length of 79 . 1987-2006 FLT 1987-2006 FLST 1987-2006 FXST 1987-2006 FXSTC

7mm valve guide ream tool. 2005-2017 FXST 2005-2017 FLST 2005-2016 FLT 2005-2017 FXD 2004-UP XL

Air cleaner kit includes a die cast mount bracket with built in breather passages and bolts and an 8 black round covered air cleaner with fileter and backing plate. 2008-UP FLH

1 black handlebars are made from heavy steel tubing with knurl spacing 2 inches apart. These have wire holes but are not drilled for internal wiring. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 1982-1984 FL 1982-1984 FX 1982-UP XL 1986-2017 FLST 1984-2017 FXST 1982-1994 FXR 1991-2015 FXD 1982-2007 FLT

8 stripe air cleaner cover features a black finish. Custom Application

1-1/4 black handlebar with 8 rise. These bars are drilled with a copper wire inside for pulling thru internal wiring and is notched for throttle by wire application. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 1982-1984 FL 1982-1984 FX 1985-UP XL 1986-2017 FLST 1984-2017 FXST 1991-2017 FXD 1984-1994 FXR

8 stripe air cleaner cover features a chrome finish. Custom Application

1-1/4 chrome handlebar with 8 rise. These bars are drilled with a copper wire inside for pulling thru internal wiring and is notched for throttle by wire application. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 1982-1984 FL 1982-1984 FX 1985-UP XL 1986-2017 FLST 1984-2017 FXST 1991-2017 FXD 1984-1994 FXR

1 Glider Handlebar has an 8 rise is chrome plated and has holes for internal wiring. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 1986-2013 FLH

Black 1-1/4 handlebar has holes for internal wiring and features throttle by wire right side notches. The 1 diameter at the clamping area is for use with 2015-up FLTR models and features a front oval wire hole. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 2007-2015 FLT

Assembly includes backing plate 8 cover filter billet breather bracket and hardware. 1993-2007 FLT 1993-2007 FXST