Mid-USA

Semi-Metalic Brake Pads Fr/Rr Gma Model"B",Jay Brake Adc & Adcs,Hardbody 2 Piston
This pair of Brake Pads are economically prices and designed to be used with small GMA calipers ADC & ADCS. The pad material is made from a semi-metallic, non-asbestos with a Kevlar base. Pad measures 1 5/8 long x 1 1/2 tall. Sold in pairs.V-FACTOR Brake Pads
Fits GMA Model B Two Piston (rear)
Fits L 4 speed 1949/1984 Custom, Converts Wide glide to Dual Disc. Use with dual lange Hub. Mounts to ender Lugs. May require removal of original factory brake Mounting Tab. Use with 10 flat rotor. XSTS Springer Softail 1988/Later and most Custom Springers, Paughco Wide Springer including our 35203, 35204, & 35205 Use 56228 Axle and 11 1/2 rotor. X and Sportster 1974/1977 Single Disc 19 wheel only, all Single Disc models 1984/1999 (except Springer & L 4 speed), and all Dual Disc models 1984/1999

Pro II Brk Sys Come Ferrule Vw45776/788 Fittings Only Brass Russell R49009

• Russell's Pro System II hose and fittings are designed for custom builders that need to easily fabricate brake or hydraulic clutch lines
• The cut to length semi-rigid black nylon hose has a ³/₁₆ O.D. for a low impact custom look yet provides improved braking effect with the same lever pressure as OE size hose. Hose is not DOT approved
• The chrome plated steel compression fittings (sold separately) are available to replace ³/₈-24 & ⁷/₁₆-24 banjo bolts as listed. The ¹/₈-27 NPT compression fittings are designed for early style or custom brake hoses drilled and tapped for pipe thread
• The 45870 male adapter end is designed for use with -3 male adapter banjo ends or brake tees found in the control section when required

Russell
Replacement Compression errules, Pack of 10

Rear Brake Master Cylinder St 00/L* & Touring 99/07 Rpls Hd 41755-99 & 41767-05A

• High quality reproduction of the OE part

V-FACTOR
Chrome Plated Rear Master Cylinder
Fits Softail 2000/Later & Touring models 1999/2007
Replaces HD# 41755-99 & 41767-05A

Foot Lever, Shift Chrome Sportster All Models 1986/1989 Rpls Hd 34606-86A & 34605-86T
These replacement foot shift levers meet or exceed the OEM specifications. See the control section for foot shift pegs.V-FACTOR
Chrome Plated oot Shift Lever
Fits Sportster & K Model 1986/1989
Replaces HD# 34606-86A & 34605-86T
(Imported)

Fender Extension,Rear For Use W/22970&22971 Tri-Bar Lights Abs Chrome Plated

• 
  
  
  
  • Chrome plated ABS rear fender extension enables 22970 or 22971 to be fitted on FLHR & FLT models 1999/Later
  
  
  • Kit is easy to install and includes all necessary hardware
  
  
  
  

(Imported)

Spotlight And Passing Light Shell Only, 4-1/2" Bottom Mount W/Hardware, Chrome
These 12 volt 4 ¹/₂ O.D. Spotlight and Passing Light Assemblies are complete as shown and ready to bolt on. See below for availability of lens. V-FACTOR
Chrome Plated 4 ¹/₂ O.D. Shell Housing & Hardware without light
Fits Dresser models 1962/Later & custom use
Replaces HD# 68667-78

Taillight Lens,Rpls Lens On Maltese Cross Taillight #11212 And #11232, Bulb Or LED Type

• Sturdy die cast chrome plated housing has a flat back for easy mounting and includes 5/16 mounting bolts on 2 centers
• Taillight measures 4 tall x 4 1/8 wide and is 1 7/8 thick
• A clear license window is also provided
• 12 volt assemblies are available with an automotive #1157 bulb or with 53 separate LED lights

Note: These tailight assemblies are not DOT approved and should be used accordingly.V-FACTOR
Replacement Red Plastic Lens

Alternator Rotor Dyna 2006 Rpls Hd 40356-06
V-FACTOR
Heavy Duty Black Rotor
Fits Dyna 2006 with 40 Amp charging system
Replaces HD# 40356-06
(Imported)

Secondary Cam Chain Tensioner Big Twin 1999/2006 Rpls Hd 39964-99A
HARDWARE
Secondary Cam Chain Tensioner
Fits 1999/2006
Replaces HD# 39964-99A

Relay, High-Low Beam Switch 12 Volt Relay Allows Use Of One Wire Horn Button Switch

• This 12 volt relay switch will let you eliminate the conventional two position high/low beam headlight switch and run a momentary switch, such as a horn type button to operate both the high and low beam functions
• Measures 1 1/4 x 1 1/4 x 1 1/4
• Includes simplified wiring instructions

Standard Motor Products
High/Low Beam switch

Starter Shaft Needle Bearing See Oem # & Catalog For Fit Rpls Hd #9063 Torrington B1210
Torrington
B1210 Outer Primary Cover/Starter Shaft Needle Bearing
Fits L 1965/1982, FLT 1980/1988, FXR 1982/1988, X 1971/1984 (except XB & XSB), XE 1985, Softail 1984/1988 and Sportster, K model 1967/1980, Big Twin 5 speed 1980/1988
Replaces HD# 9063

Brake Tool Eze Bleeder All Models W/Hydraulic Brakes Complete W/Instructions

• Bleed your brakes easily and efficiently the first time with the EZE Brake Bleeder^®
• Developed by mechanics for mechanics, this kit utilizes the law of physics by back bleeding the brake system pushing air in Fits natural direction up to the master cylinder
• Holds 40cc of brake fluid
• Includes sealed container for storage and instructions

Eze Bleeder
Includes adapters for 1/4 & 3/8 brake bleeder screws

Intake Manifold Adapter, Flange 40/44Mm Spigot Carb To 2 Bolt Flange Mount Intake Manifold
These gas resistant neoprene Intake Manifold Adapters are used to mount Mikuni and Lectron spigot style carburetors. They are available for mounting to a spigot type intake manifold or for mounting to a 2-bolt flange type manifold. V-FACTOR
Flange Type for 40/44mm carburetor
Bolt holes on 3 ⁵/₁₆ centers designed for custom 2 hole flange type intake manifold, 1 ¹³/₁₆ I.D.
Includes clamp, (Imported)

Flush mount replacement cap. Fits MID-80024 Bung Kit

• Vented gas cap pops up for easy removal and mounts flush in the down position
• Cap measures 1 ⁵/₈ O.D.

V-FACTOR
Replacement Chrome Plated Flush Mount Gas Cap with O-Ring Only

Primary Chain Tensioner M6 Kit Big Twin 01/06 Self Adjusting Spring Loaded #M6-BT01

• Spring loaded to provide constant tension on the primary chain
• Eliminates chain snatch on deceleration
• Promotes smoother shifting and less stress on transmission components
• Improves chain life
• Includes installation instructions

Hayden
Fits Big Twin 2001/2006 (except Dyna 2006)

Cam Shaft Gear Needle Bearing Sportster Late 1958/1990 Rpls Hd #9057 Torrington Bh117

Sold Each

Torrington
Cam Shaft Gear Needle Bearing
Fits K Model & Sportster Late 1958/1990
Replaces HD# 9057

Viton Valve Guide Seals Sh L81/L,80Ci,3/8"Id X.625"Od Rpls Hd 18000-81 Vs403V

• The best Valve Guide Seals available!
• Made from a very elastic fluoro-viton polymer with 5% Teflon® added to help prevent excessive valve to seal friction
• A metal garter spring retains a constant valve seal to valve tension for precise oil control
• eature a bonded steel jacket providing a secure fit to the valve guide
• Internal ribs are designed to easily slip the seal on the valve guide without the use of a valve seal installation tool, but hold snug after installed
• Sold in pack of 4

POWER HOUSE
Intake & Exhaust Valve Guide Seal
3/8 Valve O.D. & .625 Guide O.D.
Fits Shovelhead Late 1981/Later
Replaces HD# 18000-81

Exhaust Valve, Oe Style Big Twin Evo 1984/Later Rpls Hd# 18082-83

• These OE quality valves give you the option of rebuilding your worn out heads without the high cost of purchasing stainless steel valves
• Use these budget valves with confidence
• Manufactured to mirror the dimensions and materials used in the factory versions
• All head diameters, stem diameters and overall lengths are the same as OEM
• Sold Each

V-FACTOR
OE Style Exhaust Valve
Fits Big Twin Evolution 1984/Later
Replaces HD# 18082-83

Exh Valve Pan/Shv Bt 1949/84 18082-57 And 18089-80A

• These OE quality valves give you the option of rebuilding your worn out heads without the high cost of purchasing stainless steel valves
• Use these budget valves with confidence
• Manufactured to mirror the dimensions and materials used in the factory versions
• All head diameters, stem diameters and overall lengths are the same as OEM
• Sold Each

V-FACTOR
OE Style Exhaust Valve
Fits Panhead 1948/1965 & Shovelhead 1966/1984
Replaces HD# 18082-57

Brake Disc,Drilled 11.5"Od Rr Fx 4Spd 81/86 Fxr 82/L,St84/91 Spt 79/91 Flhs 81/84 Fxwg81/86

• Imported discs are made with high quality SAE 1010 IV 1020 steel or S420J2 stainless steel to be economical yet have very strong and dependable performance
• Discs are drilled for heat dispersion, weight reduction, wet weather braking and are compatible with all types of disc brake pads
• See Additional Images for illustration of mount hole style

Note: Always install new brake pads with new brake discs to ensure maximum disc pad and disc life. See the wheel section for brake pads.V-FACTOR
Drilled 11 ¹/₂ O.D. & 2 I.D. Disc
C mount hole style & ³/₈ bolt size
Fits X, XWG Rear 1981/1986, FXR Rear 1982/1991*, FLHS Rear Late 1981/1984, Softail Rear 1984/1991*, Sportster Rear 1979/1991*
Replaces HD# 41789-79A
(Imported)
* Will also fit 1992/1999 models if our 57123 mounting hardware is used

Brake Pads,Sbs 566Hlf Custom Brembo,Willwood & Revtech Four Piston Frt/Rear 566H.Hf
Rated #1 in the racing circuit, SBS brake pads offer the best performance of any brake pads available. SBS's unique ultra sonic blending process of materials provides optimum friction that prevents hot spots, glazing, brake fade and premature rotor wear. Sold in pairs.its Revtec & Wilwood Rear Calipers. (Imported)

Skeleton Hand Mirrors Fits All Models Die Cast Aluminum

• Die cast aluminum
• Includes mounting hardware
• Sold in pairs

V-FACTOR
Chrome Plated Skeleton Hand Mirror Pair
Fits all models

Master Cylinder Rebuild Kit, Fits Gma Handlebar Kits 5/8" Bore, Rbk-4
GMA
Rebuild Kit
Front Brake Master Cylinder (RH 5/8)

Handlebar Controls With Wires Fl 1972/1981 Fx Spt 1973/1981 Wide Blade Cl & Brk W/Switches

• Offered with or without switches and wiring as listed
• Available with OE style levers or wide blade levers
• The front brake master cylinder has a ³/₄ bore

V-FACTOR
Chrome Plated Wide Blade lever style kit with wires & switches
Fits L 1972/1981, X & Sportster 1973/1981 & custom applications
(Imported)