V-Twin Manufacturing

Chrome Spring Fork handlebar throttle spiral is pull type.
To activate the linkage on the Keihin Bendix carburetor, you are required to do the pulling and the linkage will open to the throttle.
OEM: 3312-42

V-Twin Manufacturing V-Twin Manufacturing Bat Front Motorcycle Fender Tip Ornament Chrome - Sold Each
Bat Front Motorcycle Fender Tip Ornament Chrome

Height- 2 1/16”

Length- 2 3/8”

Width- 2 3/16”

Dealer marketing 1340 Evolution plaque.

Chrome Rear Wheel Hub includes bearings, races, seals and seal spacers. This hub is for use on 1986-1999 FXST, XL. Constructed hub is steel, chromed.
Includes snap ring.
OEM: 40976-86A

Axle with a milled head and threaded end has a 11-1/4" bearing surface length is a great way to dress up your existing axle or to replace a worn out or damaged axle for rigid frames.

Measurements:

Chrome swingarm pivot kit. Includes races, bearings, spacers , lock tab, and pivot pin.

Swingarm rebuild kit.

Chrome rear axle spacer has an overall length 3/4".

OEM: 43654-86A

Measurements:

Overall Length: 3/4"
Inner Diameter: 3/4"

Rebuild kit includes bearing, race, snap ring, seal retainer washers, seal spacers, and the white inner spacer which is 4.4480".

Rear axle is for a single tube frame and has a 12-1/4" bearing surface length.

Tech Note:

Suggested to use with #51-3501 single tube frame

Axle has a threaded end with a 7-1/8" bearing surface length and is a great to dress up your existing axle or to replace a worn out or damaged axle.

OEM: 43895-87

Chrome outer primary cover is for 6-Speed transmission models.
Order screw kit separately. Does not have Inspection plate to accept mid shifter shaft. For use with forward controls only.
OEM: 60782-06

Chrome engine dress up kit includes rocker shaft end nuts, sprocket cover, cam cover trim, outer primary cover. This kit also includes kick starter return spring and spring stud. Chrome hardware is included to facilitate assembly.

NOTE: Kit does not include chrome rocker box cover set.

XLH 1971-1976

Chrome 5-speed outer primary cover is made from new die cast tooling to replace stock parts.
Starter shaft hole has a .98" inner diameter.

*NOTE: Must order gaskets, starter bearing and screw kit separately.

OEM: 60665-85B

Chrome 5-speed inspection cover without shifter hole.

OEM: 32519-80

Mini oil gauge kit features 1" outer diameter with 1/8" pipe fitting.

Crankcase breather vent canister features replaceable umbrella valve available separately.

Chrome crankcase breather accepts 1/8" National Pipe Thread.

Our 4 spigot chrome oil tank features 3 quart capacity and factory welded seams.

OEM: 62498-89A

Measurements:

Height Front: 6-1/4"
Height Rear: 5"
Depth: 7-1/4"
Depth of Battery: 5-1/

Electronic speedometer with tachometer starts at zero.
Certain years and models will require separate purchase of correct wiring harness and tachometer adapter. Please see tech notes.

*NOTE: Gauge reads in kilometers per hour, 0-220KPH.

*Note: Tach wire harness, required all models, all years P/N VT- 32-1336

FLST 1996-2003
FXST 1996-2003
FLHR 1996-2003
FXDWG 1996-2003

Chrome dash cover
Order bolt kit separately.
OEM: 67189-95

Measurements:

Gauge Opening: 3-9/16"

Speedometer has a ratio of 2240:60 and features built in electric tachometer, and operates from coil impulse.
Accepts a 12mm cable.

Set of white emblems with red lettering for 1959-1960 gas tanks.
Use with weld-on strip or adhesive mount strip and mount screws sold separately.
OEM: 61775-59T

Tech Note:

Suggested to use with #38-7013 adhesive mou

OE set of white emblems with black lettering for 1961-1962 gas tanks.
Use weld on emblem mount strip and mount screws sold separately.
OEM: 61776-61T

Tech Note:

Use with #38-6701 weld-on emblem mount strip