All

Stainless steel braided with a clear coat throttle and idle cable set has 45° elbow fitting. The casing length of the throttle and idle cable is 37.83 . 1981-1984 FX 1986-1989 FLST 1981-1984 FL 1984-1989 FXST 1981-1989 XL

V-Twin stainless steel braided with clear coat throttle cable has a 38 casing length with 90° elbow fitting. The ball end is 4.5mm. 0-Replacement applciation cable for 38mm Mikuni caburetor.

Polished stainless steel windshield trim with four accent slots includes stainless steel mounting hardware. 2014-UP FLH 2014-UP FLHX

Polished stainless steel windshield trim with four accent slots includes stainless steel mounting hardware. 1996-2013 FLH 1996-2013 FLHX

V-Twin piston ring set is for 3-7/16 bore and is standard size. It features two compression rings with a size of 1/16 and oil rings with the size of 3/16 . The rings need a minimum end gap of .014 when installed in the 3-7/16 cylinder. Sold as a pair. 1954-1977 FL 1971-1977 FX

Standard size cam chest breather valve gear is machined and designed to replace original ground steel units. Order 8 piece thrust washer separately. *NOTE: 28.45mm (1.1201 ) outer diameter. 1936-1940 EL 1941-1947 FL

Upright detachable passenger sissy bar is a standard height and features a chrome finish. Accepts a wide range of sissy bar pads. Easy to attach and detach. Requires docking hardware kit and detachable mount kit available separately. Will also fit FLHTC models with a detachable touring pack rack. 2009-UP FLT

Chrome standard forward control mount kit replaces the factory painted forward control mounts. Includes left and right supports and chrome mounting hardware. 2018-UP FLSB models with forward controls 2018-UP FXFB models with forward controls 2018-UP FXFBS models with forward controls 2018-UP FXBR models with forward controls 2018-UP FXBRS models with forward controls

Black rubber standard pedal rubber set fits Torrington standard pedals. Sold as a set of 4. 0-All Pre-1916 models

Standard pedal set is Torrington type with 1 right and 1 left hand nickel plated pedals with the standard pedal rubber set installed. Real rubber museum quality as used on Motorcycepedia restorations by Bruce Linsday! The kick starter pedal rod nuts are from McMaster-Carr. *NOTE: The center axle is heat treated and un-plated. 0-All early model pedal drives

Tappet set is solid type for Panheads. Units are precision machined and feature drilled holes which allow for better lubrication on valve train. Set of four. Adjusters and lock nuts included. Lightning holes allow for better lubrication on the cast iron lifter blocks. 1948-1965 FL

Star hub gasket kit includes small and large cork star gasket 2-internal snap rings and outer cork retainer washer . Six piece set. 1936-1952 EL 1941-1965 FL

Starter drive assembly for 6-speed models. 2007-2017 FXD 2007-2017 FXST 2007-2017 FLST 2007-2015 FLT Volt Tech

Starter drive assembly for 6-speed models. 2016-UP FLT Volt Tech

Includes clutch drive shaft o-ring lock tab seals spring and cable boot. 1991-2006 FXST 1991-2006 FLST 1991-2006 FLT 1991-2005 FXD 1991-1994 FXR

Starter housing gasket is for 4-speed transmissions. 1980-1984 FXSB 1980-1984 FL

Jack shaft lock wrench is zinc plated. This tool is used to hold starter gears on 1991-up Big Twins. 1991-UP FL 1991-UP FX 1991-UP FLT 1991-UP FXR

V-Twin high torque starter motor is a 1.4 kw design and features a black finish. Generates more power and shaft speed than the original type 0.8kw starter.Starter motor measures 6 in length. The screw measures 3/4 in length and 10-24 TPI. *NOTE: Hitachi style. 1974-1984 FX 1982-1984 FL 1984-1988 FXST 1984-1988 FXR 1984-1988 FLT 1974-1976 XL 1986-1988 FLST

Starter relay will reduce 12 volt voltage drop in single fire ignition applications during cranking will allow full battery voltage to the module and coil. 2004-2011 XL

Starter relay for use with the chrome lever starter system only. 1965-1984 FL 1973-1984 FX 1984-1988 FXST 1986-1988 FLST

Starter shaft housing extension has the inboard bushing. For use with the York Electric Starter Kits. 1941-1969 FL

Factory type starter shaft housing stud set. Sold as a set of two. 1965-1984 FL 1971-1984 FX 1984-1988 FXST 1986-1988 FLST

Starter solenoid rebuild kit provides complete overhaul for solenoids on stock and after marketmodels. 1981-1994 XL883 1981-1990 XL1200

Starter solenoid rebuild kit provides complete overhaul for solenoids on stock and aftermarket models. 1991-UP XL1200 1995-UP XL883

Throttle by wire grip set features a stealth tone design with black end caps. 2008-UP FLT 2016-UP FXST 2016-UP FLST 2016-2017 FXD

Custom round style mirror with black steel back and 4 round stem. Custom application

Sifton steel connecting rod bearing cage set includes 4 cages and standard size Torrington roller set. *NOTE: Are late style cages. 1929-1931 DL 1932-1936 WL 1937-1952 WL 1937-1973 G

Steel dimpled footpeg kit featuress chrome steel pegs and include male adapter blocks with zinc finish. *NOTE: These will not fit passenger on 2018-up Softail models. 1980-1986 FX 1986-UP FXST

Steel exhaust valve is for 45 Side Valve models. 1929-1952 WL 1929-1973 G

Mirror stem is stamped steel and is riveted contruction with a black oxide finish. Billet 6 single slot girder style style stem for right or left side. Order hardware and mirror head separately. 1936-1940 EL 1941-1945 FL 1934-1936 VL 1934-1952 WL 1934-1957 G 1937-1948 UL

Steering damper anchor plate kit features a cadmium plated anchor plate with parkerized bolts nuts and washers. 1952-1956 K 1952-1956 KH 1957-1963 XLCH

Steering damper handle for late 1937-42 models. Features a chrome finish and a shape that has a shorter curve at the nose than the later type. 1937-1942 EL 1937-1942 U 1937-1942 W

Steering damper handle features a parkerized finish with a shape that is more flat on the top portion for late 1936-42 models. 1937-1942 EL 1937-1942 U 1937-1942 W