All

45 mainshaft race does not include the seal *NOTE: Measures 59 x 69 x 4.8mm. 1933-1936 RL 1937-1940 W

Spring Fork installation kit with ball bearings. Installation kit includes zinc plated neck cups ball bearings upper and lower races black nut with dust cover pressed on and parkerized top nut. Use 30 ball bearings in the steering head. 1939-1957 G for 7/8 Stem Spring Forks" 1939-1952 WL for 7/8 Stem Spring Forks"

45 primary drive kit includes a 31 tooth motor sprocket. 1941-1952 W

Smooth black 3 speed shifter gate without numbers for 45 models. 1936-1946 W

45 shifter shaft set screw Sold in a pack of 5. 1938-1952 W 1938-1973 G

Tool Box kit is for 45 models with two keys included. Kit also features chrome tool box zinc plated bracket and mount kit. Bracket is bolt on installation. 1941-1952 W

Zinc plated hair pin style retainer clip is constructed of steel for 45 transmission shifter shafts. These pins are corrosion and rust resistant and may be mildly magnetic. Used on grooved shafts. 1938-1952 W

Sprocket seals kit comes with metal cups for 45 transmission. 1938-1952 WL 1941-1973 G

Front and rear cylinder with 2 pistons rings valve guides and intake manifold nipples installed. For Side Valve models. The piston measures 2.7455 with a .002 clearance and can be bored out to a maximum of 2.745 . Hasting rings and Rowe guides are included. *NOTE: The front cylinder is original army surplus and the rear cylinder is a replica with casting marks by V-Twin MFG. The cylinders include original casting marks! *NOTE: Includes VT #11-0637 Piston Kit Standard with Hastings ring set. Barrels are pre-fit to accept these pistons. Check ring gap before final assembly. Has
49-0380" Chrome spotlamp mount bar is a replica of the original Buco accessory. Bar is curved and features flat ends to accept spotlamp mount stud. 1929-1952 WL

Zinc cable ends have 1/4 x 24 threads. 1947-1973 G 1947-1952 W

Parkerized clutch cable end has a 10x32 TPI for side valve models which is the same as OEM for years listed. 1938-1946 G 1938-1946 W

45 W-WL-WR-G parts and service manual is 288 pages of original restoration and repair of the 1937-1964 G 1937-1952 W and 1946-1952 WR models. *NOTE: Includes WR factory data completed WL parts book early to late number conversion pages V-Twin 45 replacement parts and service index. **NOTE Product may not be returned. ISBN: 978-1-7327387-1-3. 1937-1952 W 1937-1973 G

Weld on hardtail assembly features a raw finish forged cross bar and rear axle plates on original WL 45 solo's. Installation requires a qualified fabricator and welder. Must be welded on and the fabricator must construct pieces to connect to frame. Caution/Note: Hardtail tubes must be cut and fit to the front section. 1936-1973 G 1936-1952 W

1936-1952 W 1936-1963 G

Kick starter arm kit features a black finish and is for 45 WL models. Kit includes a black kick starter arm a black fudgesickle kick starter pedal and a kick starter crank clamp bolt. 1937-1945 WL

45 WL kickstand spring kit includes a black spring bushing and a parkerized tab. The spring is correct for the top of the kickstand. The tab will provide the correct spring tension. 1930-1952 WL

Large 1:6 scale side valve motor model with authenthic cast pewter details. Fully assembled on a wooden display base. 0-All

Raw WL side fill oil tank features 1/8 NPT inserts to accept rubber oil lines 2 coil mounting studs on the left side and the battery box to accept 12 volt mini batteries. Tank also has a pocket built into the front of the tank to allow clearance of the stock battery box mount on the frame. Includes threaded filler cap and drain plug. Battery compartment measures: 3-3/4 deep x 4-7/8 wide x 4-1/4 high. *NOTE: Must order connector fittings separately. *NOTE: There is no need to remove the battery box tab! 1936-1952 W 1936-1963 G

Black vinyl throttle and idle cable set is +12 overstock at 46.25 . 1996-2007 FLT 1996-UP FXST 1996-UP FLST 1996-UP XL 1996-2017 FXD except FXDWG

Black Tomahawk style front fork brace for 49mm forks. Kit includes support brackets spacers and hardware for mounting. These custom front fork braces are made from laser cut 3/16 thick steel. They allow removal of the front fender and increases rigidity to the front fork better than stock eliminating any fork twist while safeguarding the integrity of the suspension. The custom styling looks great on any motorcycle for use with 23.5 front wheels and tires. 2006-2017 FXD

Chrome Tomahawk style front fork brace for 49mm forks. Kit includes support brackets spacers and hardware for mounting. These custom front fork braces are made from laser cut 3/16 thick steel. They allow removal of the front fender and increases rigidity to the front fork better than stock eliminating any fork twist while safeguarding the integrity of the suspension. The custom styling looks great on any motorcycle for use with 23.5 front wheels and tires. 2006-2017 FXD

Fork damper tube set for 49mm forks on Touring models. Sold as a pair. *NOTE: With 22000031 Ring. 2014-UP FLT

OE lower fork damper tube is for 49mm fork legs.

FXDF 2008-2016

Fork lowering kit for 49mm forks and is used to lowers forks 1-1/4 to 2 . 2014-UP FLT

Rebuild kit includes seals washers and bushings as shown. *NOTE: For both sides. 2006-2017 FXD 2006-2017 FXDL 2006-2017 FXDWG 2006-2017 FXDB 2006-2017 FXDF

Rebuild kit includes seals snap rings and bushings for both legs. 2014-UP FLT

Fork tube assembly is +4 over stock length with internals. 2006-2017 FXDWG

Fork tube assembly is +6 over stock length and features a hard chrome finish. 2006-2017 FXDWG

Gator fork boots for 49mm forks are constructed of black rubber and are 7 long. Sold in a quantity of 2. 2007-2017 FXD 2014-UP FLT 2019-UP XL 48""