BDL Industries Belt Drive Systems

BELT DRIVES LTD. Replacement Outboard Bearing Cover

• For use on BDL Belt Drive clutches

Sold as a pair.

BELT DRIVES LTD. Replacement Starter Housing For Top Fuel Belt Drive, Each

• For use on BDL Belt Drive clutches

Belt Drive Kit,8Mm W/Clutch Flt Fxr Late 1985/1989 W/Kevlar Belt Bdl Evb-1T
Chuck the chain and bolt in the belt for a smoother ride with this 8mm Enclosed Primary Belt Drive Kit from Belt Drive Limited. Designed for use without modification to the inner primary cover, these bolt-in kits feature cylindrical shaped, replaceable round clutch dogs which can withstand 1200 pounds of torque. The inner stressproof steel hub is designed to move the weight of the clutch basket inward over the mainshaft 1 which distributes the weight more evenly on the mainshaft. To ensure a low rotating weight and provide long life, both the front and rear pulleys are made of lightweight aluminum and are hard anodized. Rounding out these kits are a set of Kevlar^® clutch plates that provide 60% more surface area than the OE clutch and a Kevlar^® belt for positive performance. If more clutch plate pressure is needed, the pressure plate is designed to accept up to 6 more clutch springs if required. Each kit includes a sealed primary bearing (except kit 77028). A primary bearing seal is also included for those who don't want to change the OEM non-sealed style bearing. Change over today for a smoother, quieter ride. or replacement parts, see the drive train section for clutch or starter ring gear.

Note: Due to the numerous variables of misalignment and improper tensioning upon installation, there is no warranty on belts.

Note: No modification is required to the inner primary for installation.Belt Drives Ltd.
1 ⁵/₈ wide Belt Dive Kit with Clutch
Fits FLT & FXR models Late 1985/1989 with taper clutch hub and rear belt drive, 48-68 tooth combo

BELT DRIVES LTD. Standard Offset Spacer Insert

• Used to offset motor pulley for belt alignment
• Spacer inserts are available in eight widths from 1/4" to 2" and include a motor sprocket nut and mounting screws
• Pulleys are for 3" systems and accept any of the spacer inserts listed
• Pulleys and spacer inserts sold separately
• Made in the U.S.A.

BELT DRIVES LTD. Replacement Clutch Adjusting Screw/Jam Nut, Each

• Kits include primary chain, front sprocket and nut, chain adjuster, clutch basket and clutch assembly with Kevlar plates
• Feature new-style clutch that eliminates grabbing and dragging
• Made in the U.S.A.

BELT DRIVES LTD. Polished 2" Open Belt Drive Kit, Natural, Harley 90-06 FX 90-06 FL

• BDL's ball-bearing lockup clutch with ring gear provides ease of shifting and positive clutch engagement
• New streamlined baseplate provides a unique look
• Kits include a Kevlar 142-tooth drive belt, motor plate, starter housing and guard, stand offs, side guard and rear pulley cover with hardware
• Made in the U.S.A.

Belt Drive Part Clutch Lock Up See Catalog For Fitment W/Mounting Hrdw Bdl.Luc-100

• Centrifugal force allows the actuater arms to move outward, which applies extra pressure against the pressure plate and clutch springs for positive engagement with no clutch slippage.
• Gives you the advantage of using the lighter pull 6 clutch spring set with no clutch slippage at hard throttles.
• Works well on any size engine.
• Manufactured from hard anodized CNC machined billet aluminum.
• Includes instructions.

Lock up clutch kit for BDL clutches. Fits BDL 8mm belt drives with dome style BDL pressure plate. Note: This kit will not work with early BDL stepped dome pressure plate or open belt drive systems with dome pulley cover.

BELT DRIVES LTD. Ball-Bearing Lockup Clutch Conversion Kit, Harley 14-16 FL

• Standard equipment with all of BDL's 2" SS series primary drives
• Converts existing clutches to a ball-bearing lockup design
• Lockup design applies extra pressure to the clutch plates for positive engagement with no clutch slippage
• No increase in lever pull effort
• Kits include all necessary components for a complete retrofit
• Made in the U.S.A.

BELT DRIVES LTD. Replacement Pressure Plate

• For use on BDL Belt Drive clutches

BELT DRIVES LTD. Replacement Components For PART #1130-0112

• Kevlar clutch pack plates have 60% more surface area than stock plates for strong, positive clutch engagement
• PART #1130-0112 features a ball-bearing lockup pressure plate that will handle any application including big-inch motors
• Kit also includes inner clutch hub and diaphragm spring
• Replacement plates available
• PART # 1130-0176 features a standard pressure plate and clutch springs
• Made in the U.S.A.

BELT DRIVES LTD. Replacement Kevlar Plates For PART #1130-0112, Friction Plate Kit

• Kevlar clutch pack plates have 60% more surface area than stock plates for strong, positive clutch engagement
• PART #1130-0112 features a ball-bearing lockup pressure plate that will handle any application including big-inch motors
• Kit also includes inner clutch hub and diaphragm spring
• Replacement plates available
• PART # 1130-0176 features a standard pressure plate and clutch springs
• Made in the U.S.A.

BELT DRIVES LTD. Replacement Components For PART #1130-0112, Steel Plate

• Kevlar clutch pack plates have 60% more surface area than stock plates for strong, positive clutch engagement
• PART #1130-0112 features a ball-bearing lockup pressure plate that will handle any application including big-inch motors
• Kit also includes inner clutch hub and diaphragm spring
• Replacement plates available
• PART # 1130-0176 features a standard pressure plate and clutch springs
• Made in the U.S.A.

DRAG SPECIALTIES Steel Plate Kit, plates per package 5, Harley 84 - 90 XL

• Designed to perform under extreme heat conditions
• Allow smooth, precise shifting
• 100% asbestos free
• Kevlar plates have higher-density compound for increased durability; organic plates for OEM replacement
• Steel plates are manufactured under strict quality-control standards
• Can be run wet or dry
• Made in the U.S.A.

DRAG SPECIALTIES Steel Plate Kit, plates per package 7, Harley 84-89 FX 84-89 FL 87 - 89 XL

• Designed to perform under extreme heat conditions
• Allow smooth, precise shifting
• 100% asbestos free
• Kevlar plates have higher-density compound for increased durability; organic plates for OEM replacement
• Steel plates are manufactured under strict quality-control standards
• Can be run wet or dry
• Made in the U.S.A.

DRAG SPECIALTIES Steel Plate Kit, plates per package 6, Harley 90-97 FX 90-97 FL 90 - 16 XL Buell 94-10

• Designed to perform under extreme heat conditions
• Allow smooth, precise shifting
• 100% asbestos free
• Kevlar plates have higher-density compound for increased durability; organic plates for OEM replacement
• Steel plates are manufactured under strict quality-control standards
• Can be run wet or dry
• Made in the U.S.A.

DRAG SPECIALTIES Steel Plate Kit, plates per package 8, Harley 98-16 FX 98-16 FL

• Designed to perform under extreme heat conditions
• Allow smooth, precise shifting
• 100% asbestos free
• Kevlar plates have higher-density compound for increased durability; organic plates for OEM replacement
• Steel plates are manufactured under strict quality-control standards
• Can be run wet or dry
• Made in the U.S.A.

BELT DRIVES LTD. Ball-Bearing Lock-Up Clutch Conversion Kit, Harley 98-16 FX 98-16 FL

• Standard equipment with all of BDL's 2" SS series primary drives
• Converts existing clutches to a ball-bearing lockup design
• Lockup design applies extra pressure to the clutch plates for positive engagement with no clutch slippage
• No increase in lever pull effort
• Kits include all necessary components for a complete retrofit
• Made in the U.S.A.

BELT DRIVES LTD. Ball-Bearing Lock-Up Clutch Conversion Kit For 90-15 Primo Pro Clutch Belt Drives

• Standard equipment with all of BDL's 2" SS series primary drives
• Converts existing clutches to a ball-bearing lockup design
• Lockup design applies extra pressure to the clutch plates for positive engagement with no clutch slippage
• No increase in lever pull effort
• Kits include all necessary components for a complete retrofit
• Made in the U.S.A.

BELT DRIVES LTD. Outboard Bearing Retrofit Kit, made in the usa, Aluminum, Each

• This kit has been updated to eliminate the front pulley and engine shaft supports
• The reason for this change is that many aftermarket components used on special-construction motorcycles do not allow proper alignment of the front engine and rear transmission shaft
• Kit now supports only the rear shaft (which is all that is really required) to eliminate any problems of mis-alignment of the front and rear transmission shafts
• Works with existing BDL 3" open belt drive kits for Softails and Dyna Glide models not incorporating an outboard bearing support (kits not enclosed within the OEM inner/outer primary covers)
• Includes outboard support plate, pulley covers and all necessary hardware
• Made in the U.S.A.

BELT DRIVES LTD. Replacement Shoulder Bolts, 3/8" x 3/4", 4-Pack

• For use on BDL Belt Drive clutches

BELT DRIVES LTD. Replacement Rear Pulley Cover For PART #DS-360191/1120-0173

• For use on BDL Belt Drive clutches

BELT DRIVES LTD. Replacement Motor Plate Bearing, Each

• For use on BDL Belt Drive clutches

BELT DRIVES LTD. Black 2" Belt Drive Kit With Changeable Domes, Harley 90-06 FX 90-06 FL

• 2" drive kits loaded with style to accommodate custom trends
• All-billet construction with a unique top guard that provides long-lasting service and functionality
• Kits include a ball-bearing lockup clutch, a top belt guard and four different dome covers to allow for four different looks in one kit
• Made in the U.S.A.

BELT DRIVES LTD. Polished 2" Belt Drive Kit With Changeable Domes, Natural, Harley 90-06 FX 90-06 FL

• 2" drive kits loaded with style to accommodate custom trends
• All-billet construction with a unique top guard that provides long-lasting service and functionality
• Kits include a ball-bearing lockup clutch, a top belt guard and four different dome covers to allow for four different looks in one kit
• Made in the U.S.A.

BELT DRIVES LTD. Chrome 2" Belt Drive Kit With Changeable Domes, Natural, Harley 07-16 FL

• 2" drive kits loaded with style to accommodate custom trends
• All-billet construction with a unique top guard that provides long-lasting service and functionality
• Kits include a ball-bearing lockup clutch, a top belt guard and four different dome covers to allow for four different looks in one kit
• Made in the U.S.A.

BELT DRIVES LTD. Black 2" Belt Drive Kit With Changeable Domes, Harley 07-16 FL

• 2" drive kits loaded with style to accommodate custom trends
• All-billet construction with a unique top guard that provides long-lasting service and functionality
• Kits include a ball-bearing lockup clutch, a top belt guard and four different dome covers to allow for four different looks in one kit
• Made in the U.S.A.

BELT DRIVES LTD. Black 2" Belt Drive Kit With Changeable Domes, Harley 07-13 FX 07-16 FL

• 2" drive kits loaded with style to accommodate custom trends
• All-billet construction with a unique top guard that provides long-lasting service and functionality
• Kits include a ball-bearing lockup clutch, a top belt guard and four different dome covers to allow for four different looks in one kit
• Made in the U.S.A.

BELT DRIVES LTD. Chrome 2" Belt Drive Kit With Changeable Domes, Natural, Harley 07-13 FX 07-16 FL

• 2" drive kits loaded with style to accommodate custom trends
• All-billet construction with a unique top guard that provides long-lasting service and functionality
• Kits include a ball-bearing lockup clutch, a top belt guard and four different dome covers to allow for four different looks in one kit
• Made in the U.S.A.

BELT DRIVES LTD. Chrome 2" Belt Drive Kit, Harley 07-16 FL

• Include BDL's ball-bearing lockup clutch, new full-coverage side guard and top mesh belt guard
• Kits also include motor plate and a 132-tooth belt
• 2" drive width allows for the use of stock floorboards
• Made in the U.S.A.

BELT DRIVES LTD. Chrome 2" Open Belt Drive Kit, Harley 06-16 FX 07-16 FL

• BDL's ball-bearing lockup clutch with ring gear provides ease of shifting and positive clutch engagement
• New streamlined baseplate provides a unique look
• Kits include a Kevlar 142-tooth drive belt, motor plate, starter housing and guard, stand offs, side guard and rear pulley cover with hardware
• Made in the U.S.A.

BELT DRIVES LTD. Black 2 3/4" Open Belt Drive Kit, Harley 06-16 FX 07-16 FL

• Feature BDL's ball-bearing lockup clutch with ring gear
• Kits include motor plate, 52-tooth front pulley, 142T-belt, starter housing and guard, stand-offs, side guard and rear pulley cover with hardware
• Made in the U.S.A.

BELT DRIVES LTD. Chrome 2 3/4" Open Belt Drive Kit, Natural, Harley 06-16 FX 07-16 FL

• Feature BDL's ball-bearing lockup clutch with ring gear
• Kits include motor plate, 52-tooth front pulley, 142T-belt, starter housing and guard, stand-offs, side guard and rear pulley cover with hardware
• Made in the U.S.A.

BELT DRIVES LTD. 1" Closed Belt Drive Kit, made in the usa, Each, specific application, teeth 142, Harley 07-13 FX 07-16 FL

• One of BDL's original closed primary belt drives
• Kit includes 52-tooth front pulley, 142T-belt, complete clutch kit with ring gear and ball bearing pressure plate and hardware
• Clutch features 12 cylindrical replaceable clutch dogs, which allow clutch plates to maintain constant contact
• Kevlar clutch plates allow maximum performance with improved ball-bearing pressure plate
• Made in the U.S.A.

BELT DRIVES LTD. Polished Electric Start 8mm Belt Drive With Lockup Clutch, Harley 90-93 FX 90 - 93 XL

• 15/8" kits include front pulley, belt, clutch hub, clutch basket and Kevlar clutch set (consists of two half plates, four full plates and five steel drive plates)
• Direct bolt-in applications
• 3" electric start kits include front pulley, belt, clutch hub and clutch basket and Kevlar clutch set (consists of two half plates, four full plates and five steel drive plates), 6061 T-6 billet motor plate, outside guard and polished pulley cover
• All systems come with the Quiet Clutch and ball-bearing lockup design pressure plate
• Lockup design applies extra pressure to the clutch plates for positive engagement with no clutch slippage
• No increase in lever pull effort
• Rear pulley has a 40mm, double-row bearing with an inner stress-proof steel clutch hub to support the clutch
• Replacement components available separately; see page ???
• Made in the U.S.A.