Best selling products

Wheel, 40 Spoke 21 X 2.15 Fxst/Fxdwg 84/99 Sd 5/16 Holes Chrome

• Drop center steel rims
• Chrome spokes
• Available with OE chrome hubs
• Includes bearings and seals

V-FACTOR
OE Hub with 40 Spokes
Front Single ⁵/₁₆ lange
Tapered ³/₄ Bearing
21 x 2.15 Size
Fits FXST & FXDWG 1984/1999
(Imported)

Brake Hose Asy,Clear Coat Chrome #3 Hose W/Female Ends Use W/Fittings 23"Long R58072S
Russell Cycleflex Universal series incorporates the beauty of quality show chrome with the convenience of fitting and choice backed by the reliability of factory assembly. Cycleflex hose reduces brake line expansion, minimizing brake fade. These universal series hoses are DOT approved. Use our wide selection of #3 adapter fittings and hose lengths to allow precise fitment to your motorcycle if you are replacing stock factory hose or working on a custom brake system. All adapter fittings are chrome plated except brake light switch banjo bolt 45503. Additional brake line fittings are located in the control section.Russell
Clear Coated #3 Braided Stainless Steel 23 Brake Hose with Chrome Ends

Spdo Cable,Armor Coat 43" Long 16Mm Spdo Nut/Ft Whl Dr Rpls Hd67048-83A Mopro 66-0132
These cables for Harley-Davidson^® speedometers fall into three groups depending on upper and lower end fittings. In order to simplify the listing of these cables, we have listed them in the charts below in sequence by type housing and length. If extra length is needed just order longer length in the same group. By using this listing method we are able to reduce part numbers. Those parts with * have nylon lined housings and are manufactured by Motion-Pro in the USA.Motion Pro
Braided Stainless Steel, 43 housing length
16mm Top Nut for at Bob Speedo. No Nut for front wheel drive
Fits XLH 883 & Deluxe 883 1986/1990, XLH 1100 1986/1987, XLH 1200 1988/1992, FXRC 1985/1987, FXRP 1986/1988, FXRS-SP 1985/1986, XLS 1983/Early 1984
Replaces HD# 67048-83A

Speedometer Cable,Vinyl 34-1/4 12Mm Top Spdo Nut/Fr Whl Drive 67026-81 67072-87B 67079-86A
These cables for Harley-Davidson^® speedometers fall into three groups depending on upper and lower end fittings. In order to simplify the listing of these cables, we have listed them in the charts below in sequence by type housing and length. If extra length is needed just order longer length in the same group. By using this listing method we are able to reduce part numbers. Those parts with * have nylon lined housings and are manufactured by Motion-Pro in the USA.V-FACTOR
Black Vinyl Cable, 35 Length
12mm Top Nut for small speedometers. No Nut for front wheel drive
Fits L 1981/1984, FLHS 1987/1994, LST 1986/1990, LSTC 1987/1995, LST 1990/1995, LSTN 1993/1995, FLTC 1987/1991, FLTCU 1989/1995, FLTCUI 1996, XDB-D 1992, XDB-S 1991, XDC 1992, XDL 1993/1994, FXRS 1988/1992
Replaces HD# 67026-81, 67072-87, 67072-87B& 67079-86A

Brake Hose Asy,Rr Clear Coat Dyna Models 1991/1999 Rpls Hd 40956-90 Hd9219-A
Upgrade your existing brake lines with these Clear Coat braided stainless steel brake lines. Unlike the OE rubber brake lines that expand under pressure and give you a spongy brake feel, these braided stainless steel covered brake lines retain flexibility while eliminating pressure expansion and providing a positive brake feel. To enhance their good looks and protect the braided portion of the brake line from rubbing against any other parts, a Clear Coat has been applied. This Clear Coat is UV resistant to help prevent yellowing or hardening from weather. All ends, junctions and brake tees are chrome plated for years of corrosion resistant good looks. All measurements are given in total length, end to end. To aid in brake line identification, the brake line ends and junctions are identified below.Goodridge
Dyna Rear. Dyna models 1991/Later. Ends & K. Junction O. Includes two 10mm banjo bolts with washers. 20. (Imported)

Brake Hose,#3 Braided 4'Roll Use W/Goodridge Reusable Brake Fittings & All Brake Fluids
Goodridge cut to length #3 braided stainless steel brake/hydraulic clutch hose is designed to outperform the OE style rubber hose by not expanding under pressure. It will give you a more positive feel at the lever while providing a greater degree of safety. or improved fluid transfer, the smooth bore inner liner is made of P.T..E. (the same slick material used on frying pans) and is compatible with any type of brake fluid. All parts in this system are reusable, easy to assemble and chrome plated unless indicated otherwise. All reusable ends include a brass ferrule. Use tool 40200 to simplify installation of the brass ferrule.Goodridge
Non-Coated Braided Stainless Steel Hose
4 oot Roll, (Imported)

Brake Hose,#3 Braided 25'Roll Use W/Goodridge Reusable Brake Fittings & All Brake Fluids
Goodridge cut to length #3 braided stainless steel brake/hydraulic clutch hose is designed to outperform the OE style rubber hose by not expanding under pressure. It will give you a more positive feel at the lever while providing a greater degree of safety. or improved fluid transfer, the smooth bore inner liner is made of P.T..E. (the same slick material used on frying pans) and is compatible with any type of brake fluid. All parts in this system are reusable, easy to assemble and chrome plated unless indicated otherwise. All reusable ends include a brass ferrule. Use tool 40200 to simplify installation of the brass ferrule.Goodridge
Non-Coated Braided Stainless Steel #3 Hose
25 oot Roll, (Imported)

Cl Cable, Black Vinyl 51" Lg Sportster 1957/1970 Rpls Hd #38619-57A
Cable features an adjusting sleeve to eliminate the OE adjuster at the lever mount. See the helpful hint under clutch cables for cable description and housing construction. Motion Pro
51 Length
Fits Sportster models 1957/1970 with OE type hand lever assembly with worm gear clutch actuator
Replaces HD# 38619-57A

Th Cable,Braided Clr Coat 43" Bt 81/89 Spt 81/85 W/Oe,S&S E/ G Carb No Hd#
its on Big Twin 1981/1989 and Sportster 1981/1985 with OE type dual pull throttle and Keihin carburetor. Also fits S&S E and G model carburetors. See the helpful hint under throttle/idle cables for cable description and housing construction.Motion Pro Armor Coat
43 Length, 45° Bend Throttle Cable
Fits Big Twin 1981/1989 & Sportster 1981/1985 with OE type dual pull throttle & Keihin carburetor, S&S E and G model carburetors

Idle Cable,Blackout,38" Long Big Twin 96/L* W/Oe Cv Carb Rpls Hd56328-96 .06-2279

• Bright silver textile weave
• Clear Armor Coat protects chrome & painted surfaces
• Premium chrome fittings
• LW (lontitudinally-wound) clutch cables resist compression under heavy loads to deliver a precise, positive, non-mushy feel for enhanced clutch performance

Motion Pro Blackout
43 Idle Cable
Fits FLHT & FLTR 1996/Later
Replaces HD# 56328-96

Idle Cable,Blackout,34-1/2" Lg Big Twin 96/L* W/Oe Cv Carb Rpls Hd56342-96 .06-2267

• Bright silver textile weave
• Clear Armor Coat protects chrome & painted surfaces
• Premium chrome fittings
• LW (lontitudinally-wound) clutch cables resist compression under heavy loads to deliver a precise, positive, non-mushy feel for enhanced clutch performance

Motion Pro Blackout
34 1/2 Idle Cable
Fits Softail 1996/2000 (except XSTS)
Replaces HD# 56342-96

Sprocket Tooth Pick-Up Sensor Uw #48062 Or #48063 Only Reads Rear Sprocket Tooth #Sen-1019

• Odyssey Series II, 2 ¹/₁₆ O.D.
• Designed with the chopper in mind, these gauges do not require any hard to hide external module
• Gauges are sold separately and will require the appropriate housing cover and mounting bracket as needed
• Speedometers will also require the appropriate sensor, adapter or sending unit as listed
• The gauges feature high visibility digital numerals that are easy to read in full sunlight and include a non-glare high contrast lens
• All calibration is done with the function button
• The tachometer features an adjustable warning point to flash the gauge readout and includes a high RPM readout

Dakota Digital
Required Sprocket Tooth (Universal) Sensor
Designed to pick up off the teeth of a steel sprocket or a steel transmission pulley
Requires a fabricated mounting bracket with a ¹/₂ hole for the sensor
40 lead wire

Speedometer,Rear Whl Sensor Use W/2000 Series Spdo,Sensor Mt On Rr Axle Spacer, Rig/St

• 2000 Series
• Can be used with carbureted or fuel injected models
• Includes mounting hardware for use with stamped steel type dash 1947/1967 or die cast type dash 1968/Later
• Push-button speedometer calibration for when final drive ratio or tire diameter has been altered
• Works with electronic or 12 volt point type ignition systems with single or dual fire coil
• Built-in speed output signal for models equipped with an automatic turn signal cancel module or cruise control
• Display intensity can be reduced for night time use if a remote switch is installed
• Maximum speed readout is 255 MPH
• Maximum odometer readout is 99,999.9 and the maximum tripometer readout is 999.9
• Super bright fluorescent teal green displays are easy to see in direct sunlight
• Includes 18 speed adapter 48618 for use with 1996/Later models equipped with electronic speed sensor
• Includes non-glare scratch resistant lens with chrome trim ring
• 2 year warranty against manufacturer defects
• Includes instructions

Note: Speedometers for 1995/Later models can be used with the OE transmission sensor when used with the included adapter. All other applications require a specialized sensor listed below.

Display Features:

• Quick response bar graph type tachometer with adjustable shift point indicator (can be used on engines with 1 to 15 cylinders)
• The tachometer functions between 350 & 8,000 RPMs
• Resetable countdown service meter (with warning)
• Hour meter
• Includes a feature to recall your high speed and RPM
• unctions include 0-60 MPH timer, ¹/₄ mile timer and ¹/₄ mile speed
• Integrated Voltmeter (with low voltage warning)
• Includes following indicators: turn signal, high beam, neutral, security warning, gear position indicator (compatible with 3/6 speed transmissions), adjustable RPM warning indicator with an output for an external shift light, low oil pressure, wait to start (for fuel injected models) and check engine (for fuel injected models)
Dakota Digital
Polished Aluminum Rear Axle Spacer Mounted Sensor
Clamps to the 1 ¹/₈ O.D. spacer and reads off of the sprocket/pulley bolts

Speedometer Seal For Fatbob Speedo 68/95 Rpls Hd 67190-89
V-FACTOR
Rubber Damper
Fits 1968/1995 with cast dash
Replaces HD# 67190-89
(Imported)

Rubber Dash & Oil Tank Mount Fxs Fxef Fxb 77/84,5/16"-18 Stud W/5/16-18 Female,50235-63

• Designed to help isolate the vibration that is transmitted to the oil tank
• Also used for battery carrier trays, instrument dash panels and custom oil tanks
• All mounts are made with an exclusive rubber compound and feature heat-treated steel studs that exceed OEM specifications
• Heavy-duty mounts are absolutely the strongest available with their superior tensile strength, shear resistance and anti-sag qualities
• Mount bodies are 1 long x 1 O.D.
• Manufacturer's 2 year warranty
• Sold Each

D&S Performance
Standard Duty, Thread Size & Length: 5/16-18 x 1/4 emale & 5/16-18 x 1/2 Male
Replaces HD# 50235-63

Instrument Panel Trim Rubbers Late Die Cast Dash Fl Style Replaces Hd 71295-68

• Solid die cast replicas with finishes as listed below
• Includes decal, trim rubbers, lenses and dividers used between the bulbs
• Fits at Bob tanks with late style dash base as listed

V-FACTOR
Replacement Trim Rubbers Pair for 48114, 48115 & 48129
Replaces HD# 71295-68

Ins Panel Hrdw,Mt Screw & Stud Bt 47/67 2 Or 3 Light Panel Rpl Hd 71067-47 & 71075-47
V-FACTOR
Complete Kit with chrome cover screw
Fits Big Twin 1947/1967 2 & 3 light stamped steel style instrument panels
Also fits 48125 smoothie dash cover found in the control section
Replaces HD# 71067-47 & 71075-47
(Imported)

Dual 2 5/8" Gauge Bracket Fits 1-1/4" T-Bars,Flat Mount Polished Billet Alum 9084Md

• Designed for use with our Pro-Cycle by Autometer tachometers and speedometers found in the control section, but can also be used with other brands that have a 2 ⁵/₈ cup size
• Includes internal O-ring for clampless gauge mounting
• CNC machined from billet aluminum
• See the control section for longer riser clamp bolts with spacers

Cycle Performance
Polished Dual Gauge
Fits custom T-Bars with 1 ¹/₄ O.D. pullback risers
lat angle, 3 ¹/₂ mounting centers

Instrument Panel Kit,L Style Softail 1996/1999 & Dyna Wide Glide 1996/1998 W/Hardware

• One simple kit supplies you with everything needed (except the speedometer) for a late style instrument panel
• Die cast instrument panel (Replaces HD# 71254-96) is a faithful reproduction of the original and includes a stick-on ignition switch name plate and a lens strip for the indicator bulbs and 5 light sockets with 8 wire leads
• This is a plug-in style ignition switch with round type keys and all necessary mounting hardware is also included as shown

V-FACTOR
Chrome Plated Kit
Fits Softail 1996/1999 & XDWG 1996/1998
(Imported)

Custom Smoothie Ins Panel Cvr Fatbob Gas Tanks W/Large Spdo W/O Ins Light & Ign Sw Holes

• Dash cover features indicator lights
• Ignition switch holes have been removed for that clean custom look

V-FACTOR
Chrome Plated Dash Cover
Fits over large at Bob style speedometer with 2 light, 3 light or late model instrument baseplate and 2 piece at Bob style gas tanks
(Imported)

• Encased in all stainless steel body that is 1 7/8" O.D. x 1 3/4" long, with a 2 1/8" O.D. x 1/4" thick bezel
• A glass lens covers a 1 5/8" face
• Illuminated with a 12 volt bulb and includes two feet of lead wire
• Includes mounting bracket with 5/16" mounting hole and installation instructions

V-FACTOR
Stainless Steel with Black Face
Reads up to 8,000 RPM
Fits custom applications (12 volt)

Custom Mini Speedo,2:1 Ratio Fx,Fxr 1973/1990,Spt 1973/1990 W/Fr Whl Dr Ss Case Cp Hrdw

• Chrome Plated reinforced handlebar clamp with a rubber insulator to minimize vibration
• Designed to fit most bikes with stock length forks without any adapters or modifications
• Instrument measures 2 ⁵/₈ O.D. by 2 ¹/₁₆ deep
• 140 MPH face

V-FACTOR
Stainless Steel Gauge with Chrome Plated Clamp & 2:1 Ratio
Fits X, FXR 1973/1990 & Sportster 1973/1990 with front wheel drive
No cable included, (Imported)

Speedometer, Fat Bob 2:1 16Mm Fl 47/67 Fl Fx Fxr XL 81/84 Bullseye Face

• 120 MPH faces
• Will fit all at Bob instrument panels with dash mounted speedometers
• Designed for use with 12 mm or 16mm speedometer cable nut as listed below
• Requires 48235 tripometer reset knob (not included)

Note: These speedometers do not incorporate the circuitry required for models with self-cancelling turn signals.V-FACTOR
1946/1947 ace style, 2:1 drive ratio
Fits transmission drive L 1947/1967, front wheel drive L, X, FXR & Sportster 1981/1984 (except Softail & XWG) for 16mm Cable (Imported)

Speedometer, Fat Bob 2:1 16Mm Fl 47/67 Fl Fx Fxr XL 81/84 Tombstone Face

• 120 MPH faces
• Will fit all at Bob instrument panels with dash mounted speedometers
• Designed for use with 12 mm or 16mm speedometer cable nut as listed below
• Requires 48235 tripometer reset knob (not included)

Note: These speedometers do not incorporate the circuitry required for models with self-cancelling turn signals.V-FACTOR
1962/1967 ace style, 2:1 drive ratio
Fits transmission drive L 1947/1967, front wheel drive L, X, FXR & Sportster 1981/1984 (except Softail & XWG) for 16mm Cable (Imported)

Tapered Mirror,Right,Black Fits All Mdls 1965/Later* Short Stem Rpls Hd 91982-03B

• Custom tapered mirrors in finishes listed below
• Offered in left or right hand fitment as listed
• No rear fasteners for a clean look

V-FACTOR
Black Right Mirror, Short Stem
Fits all models 1965/Later
Replaces HD# 91982-03B