Best selling products

IRC NR-53 2.50-18 Front/Rear Tire, Bias, 40L, B-W, Moped

• High-quality moped and small cc motorcycle tires
• Front or rear application, unless noted
• Blackwall
• Tube type (TT)
• L-rated for speeds up to 74 mph, P-rated for speeds up to 93 mph or S-rated for speeds up to 112 mph

• Top quality drag pipes for models listed
• Chrome plated or black primer that is suitable for heat wrapping. Black primer is a protectant for rust, not a ceramic heat coating
• Available in 1 3/4 or 2 diameter in 40 lengths
• Slash cut tips for a performance look
• Hidden channels for a clean look

V-FACTOR
1 3/4 Chrome Plated Set
Fits Sportster 1957/1985 (except 1979)

Slash Cut Drag Pipes, 2" Sportster 1986/2003 40" Long, Channel Mounting

• Top quality drag pipes for models listed
• Chrome plated or black primer that is suitable for heat wrapping. Black primer is a protectant for rust, not a ceramic heat coating
• Slash cut tips for a performance look
• Hidden channels for a clean look

V-FACTOR
2" Chrome Plated Set
Fits Evolution Sportster 1986/2003

Air Filter Element Flt Models 2008/Later* Rpls Hd 29633-08

• Engineered for increased performance
• Washable and reusable high flow 4-layer cotton element increases air flow while offering unmatched filtration for long engine life
• Not only will these filters increase horsepower in stock engines, they are a must when performance upgrades have been done your motorcycle
• Sold each

V-FACTOR
Air ilter Element, 1 3/4 width
Fits FLT models 2008/Later
Replaces HD# 29244-08

Chuck the chain and bolt in the belt for a smoother ride with this 8mm Enclosed Primary Belt Drive Kit from Belt Drive Limited.
Designed for use without modification to the inner primary cover, these bolt-in kits feature cylindrical shaped, replaceable round clutch dogs which can withstand 1200 pounds of torque. The inner stress proof steel hub is designed to move the weight of the clutch basket inward over the mainshaft 1 inch which distributes the weight more evenly on the mainshaft. To ensure a low rotating weight and provide long life, both the front and rear pulleys are made of lightweight aluminum and are hard anodized. Rounding out these kits are a set of Kevlar^® clutch plates that provide 60% more surface area than the OE clutch and a Kevlar^® belt for positive performance. If more clutch plate pressure is needed, the pressure plate is designed to accept up to 6 more clutch springs if required. Each kit includes a sealed primary bearing (except kit 77028). A primary bearing seal is also included for those who don't want to change the OEM non-sealed style bearing. Change over today for a smoother, quieter ride.

Note: Due to the numerous variables of misalignment and improper tensioning upon installation, there is no warranty on belts.

Note: No modification is required to the inner primary for installation.

1-5/8" wide Belt Dive Kit with Clutch

Fits FLT & FXR models Late 1985/1989 with taper clutch hub and rear belt drive, 48-68 tooth combo

Sprocket,Trn.310"Offset Kit 24 Tooth Bt 4 Spd W/Disc Brake Sprocket & Wheel Spacer W/Hrdw
This Transmission Sprocket and Rear Sprocket Offset Spacer Kit eases the pain of installing wider rear tires. Kit includes a chrome plated rear sprocket spacer, .310 thick, and chrome mounting hardware designed for use with flange type steel rear wheel hub. When using on models with an open primary, a belt drive style transmission mainshaft bearing support must be used. When using electric start a rear belt drive style inner primary and appropriate starter motor must be used. As with any wide tire application always check all clearances.

Fits Big Twin 4 speed with rear disc.

24 Tooth Sprocket Kit. (Imported)

Cam Chain Tensioner Pad Kit Twin Cam 1999/2006

• Chain tensioner pads are an item overlooked and when they fail, major issues can occur
• These pads work on the inner and outer tenioners and are made from a high performance polymide stanyl that surpasses the OEM material
• Sold as a kit with one pad and one pin

Cam Chain Tensioner Pad Kit
Fits Twin Cam 1999/2006

Semi-Metalic Brake Pads Fr/Rr Gma Model"B",Jay Brake Adc & Adcs,Hardbody 2 Piston
This pair of Brake Pads are economically prices and designed to be used with small GMA calipers ADC & ADCS. The pad material is made from a semi-metallic, non-asbestos with a Kevlar base. Pad measures 1 5/8 long x 1 1/2 tall. Sold in pairs.V-FACTOR Brake Pads
Fits GMA Model B Two Piston (rear)
Fits L 4 speed 1949/1984 Custom, Converts Wide glide to Dual Disc. Use with dual lange Hub. Mounts to ender Lugs. May require removal of original factory brake Mounting Tab. Use with 10 flat rotor. XSTS Springer Softail 1988/Later and most Custom Springers, Paughco Wide Springer including our 35203, 35204, & 35205 Use 56228 Axle and 11 1/2 rotor. X and Sportster 1974/1977 Single Disc 19 wheel only, all Single Disc models 1984/1999 (except Springer & L 4 speed), and all Dual Disc models 1984/1999

Pro II Brk Sys Come Ferrule Vw45776/788 Fittings Only Brass Russell R49009

• Russell's Pro System II hose and fittings are designed for custom builders that need to easily fabricate brake or hydraulic clutch lines
• The cut to length semi-rigid black nylon hose has a ³/₁₆ O.D. for a low impact custom look yet provides improved braking effect with the same lever pressure as OE size hose. Hose is not DOT approved
• The chrome plated steel compression fittings (sold separately) are available to replace ³/₈-24 & ⁷/₁₆-24 banjo bolts as listed. The ¹/₈-27 NPT compression fittings are designed for early style or custom brake hoses drilled and tapped for pipe thread
• The 45870 male adapter end is designed for use with -3 male adapter banjo ends or brake tees found in the control section when required

Russell
Replacement Compression errules, Pack of 10

Rear Brake Master Cylinder St 00/L* & Touring 99/07 Rpls Hd 41755-99 & 41767-05A

• High quality reproduction of the OE part

V-FACTOR
Chrome Plated Rear Master Cylinder
Fits Softail 2000/Later & Touring models 1999/2007
Replaces HD# 41755-99 & 41767-05A

Foot Lever, Shift Chrome Sportster All Models 1986/1989 Rpls Hd 34606-86A & 34605-86T
These replacement foot shift levers meet or exceed the OEM specifications. See the control section for foot shift pegs.V-FACTOR
Chrome Plated oot Shift Lever
Fits Sportster & K Model 1986/1989
Replaces HD# 34606-86A & 34605-86T
(Imported)

Fender Extension,Rear For Use W/22970&22971 Tri-Bar Lights Abs Chrome Plated

• 
  
  
  
  • Chrome plated ABS rear fender extension enables 22970 or 22971 to be fitted on FLHR & FLT models 1999/Later
  
  
  • Kit is easy to install and includes all necessary hardware
  
  
  
  

(Imported)

Starter Part,Solenoid Boot Blk Big Twin 65/88 Spt 67/80 Rpls Hd 31444-65A & 31475-77
Starter solenoid boot meets and exceeds OEM specifications.V-FACTOR
Black Rubber Boot
Fits Big Twin 1965/1988 & Sportster 1967/1980
Replaces HD# 31444-65A & 31475-77
(Imported)

Handlebar Cl Safty Switch Cl Interlock Safety Sw Bt Spt 07/L* Rpls 71584-96A,71620-08

• Best quality replacement handelbar clutch interlock safety switch
• Fits models listed
• Sold each

V-FACTOR
Clutch Interlock Safety Switch
Fits Big Twin & Sportster 2007/Later, Touring Models 2007/2013, Softail models, 2007/2010, Dyna models 2007/2011 & Sportster 2008/2013
Replaces HD# 71584-96A & 71620-08

Spotlight And Passing Light Shell Only, 4-1/2" Bottom Mount W/Hardware, Chrome
These 12 volt 4 ¹/₂ O.D. Spotlight and Passing Light Assemblies are complete as shown and ready to bolt on. See below for availability of lens. V-FACTOR
Chrome Plated 4 ¹/₂ O.D. Shell Housing & Hardware without light
Fits Dresser models 1962/Later & custom use
Replaces HD# 68667-78

Taillight Lens,Rpls Lens On Maltese Cross Taillight #11212 And #11232, Bulb Or LED Type

• Sturdy die cast chrome plated housing has a flat back for easy mounting and includes 5/16 mounting bolts on 2 centers
• Taillight measures 4 tall x 4 1/8 wide and is 1 7/8 thick
• A clear license window is also provided
• 12 volt assemblies are available with an automotive #1157 bulb or with 53 separate LED lights

Note: These tailight assemblies are not DOT approved and should be used accordingly.V-FACTOR
Replacement Red Plastic Lens

Duster with zipout liner, Leg straps, & removable Cape (Buffalo)
Black Duster in Buffalo Leather. 2 front button pockets, with removable zip out liner, leg straps, and removable cape. Black Hardware.

V-Twin Manufacturing Front Engine Bar Spacer 48-53 BT Wishbone - PR

Front engine bar spacer will fit wishbone frames.

OEM: 49059-48

FL 1948-1953

V-Twin Manufacturing 16" Raw Rear 3-4" Motorcycle Axle - Sold Each

Raw axle with 3/4" threaded ends and a 13-7/8" bearing surface length is a great way to dress up your existing axle or to replace a worn out damaged axle.
These axles features 1" of 3/4" x 16 threads at each end. An acorn, pike, or nyloc nut can be

V-Twin Manufacturing Vented Breather Canister, Chrome, Breather - Sold Each

Chrome vented breather canister accepts 1/8" National Pipe thread with fittings included.

Custom application

V-Twin Manufacturing Speedometer Drive Unit, Chrome, Left Side, .461 1.277 1988-95 FXSTS - Sold Each

Left side speedometer drive is for front wheel only and for 2240:60 speedometer.
Speedometer drive has a .750 axle hole and includes a spacer with a width of .461 and an overall length of 1.277.
OEM: 67166-88

FXSTS 1988-1995

V-Twin Manufacturing Ultima Performance Motorcycle Carburetor - Sold Each
Ultima Performance Carburetor Kit Ultima performance carburetor will accept S&S jets, and S&S bolt pattern air filter assemblies. This shorty carburetor has a relocated accelerator pump nozzle for increased throttle response, and thunder jets a

V-Twin Manufacturing Velocity Stack Screen Stainless Steel, S&S Carbs - Sold Each

Stainless steel velocity stack screen.

Replacement application for velocity stack

Tech Note:

Replacement screen for #34-1160 and #34-3915 velocity stacks .

V-Twin Manufacturing 7" Headlamp Ring Rim Contoured Style Chrome, 1983-Up, 69604-03 - Sold Each

Chrome contoured rim is used on 7" diameter shells.

OEM: 69604-03

FLT 1983-UP
FLHR 1994-UP