All

Black large brake pedal pad. 1986-UP FLST 1980-UP FLT

Chrome large brake pedal pad. 1986-UP FLST 1980-UP FLT

Chrome male end mount footpeg set features drop down style pegs with a unique soft rubber pad to reduce vibration. *NOTE: These will not fit passenger on 2018-up Softail models. 0-All models with female mounting block

Large rear pad for wide type FLT models includes 6 suction cups on underside so there's no damage to paint. The pad is Lick and Stick style and features a black vinyl construction. Attaches to rear fender with multiple suction cups without damage to paint or fender. Custom application

Cast iron large VL side car toy is a collectible from the original models of the 1920's last for generations. 0-All

Layback LED tail lamp features a clear lens. Includes red yellow and black wires for connection. *NOTE: D.O.T. approved. 1999-UP FLT 1999-UP XL 1999-UP FXST 1999-2017 FXD

LED tail lamp with a red lens includes 2 styles of electrical connectors. The two styles of electrical connectors are included and one is used for 1999-2003 models and the other connector is to be used for 2004-up models. The license plate window faces up on this tail lamp. *NOTE: D.O.T approved 1999-UP FLT

LED tail lamp with a red lens includes 2 styles of electrical connectors. The two styles of electrical connectors are included and one is used for 1999-2003 models and the other connector is to be used for 2004-up models. The license plate window faces down on this tail lamp. *NOTE: D.O.T approved 1999-UP FLT

LED tail lamp with a smoked lens includes 2 styles of electrical connectors. The two styles of electrical connectors are included and one is used for 1999-2003 models and the other connector is to be used for 2004-up models. The license plate window faces up on this tail lamp. *NOTE: D.O.T approved 1999-UP FLT

LED tail lamp with a smoked lens includes 2 styles of electrical connectors. The two styles of electrical connectors are included and one is used for 1999-2003 models and the other connector is to be used for 2004-up models. The license plate window faces down on this tail lamp. *NOTE: D.O.T approved 1999-UP FLT

Real leather solo seat featuers a smooth finish. The top mounts measure 6-7/8 center to center and the bottom mounts measure 3 center to center. *NOTE:Must order springs and related brackets separately. **Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. Custom application for rigid frames

Black leather solo seat with panel top and seams. The back mounting bolts are 7-1/4 from center to center and the front bolts are 3-1/4 from center to center. *NOTE: Threads are 6mm. Custom application

Tail lamp 6 volt bulb with red LEDs. Replaces stock bulb. 0-All tail lamps

LED tail lamp assembly is constructed of black aluminum billet and features a bullet style. Assembly includes a license bracket. Custom application

LED tail lamp assembly is constructed of chrome aluminum billet and features a bullet style. Assembly includes a license bracket. Custom application

Bullet turn signal set features a black finish with amber lens and amber LED. Custom application

Bullet turn signal set features a black finish with red lens and amber LED. Custom application

Bullet turn signal set features a brass finish with red lens and amber LED. Set is cast solid. May have pits and marks from the hand casting process. Custom application

Speedometer and tachometer combination unit has a 5 LED face and is programmable to 1:1 2:1 or 2240:60 ratios with cable drive for speedometer. Features red engine/oil blue high beam green neutral and yellow turn signal lights. Includes connection to accept 12mm or 5/8 with brass nut cable fittings. Tachometer is impulse type with one wire to the ignition coil. Custom application

Fender mount tail lamp with alloy bracket and clear LED lens with 16 red and 5 white. *NOTE: For show or decorative use only and is not D.O.T. approved. ECE approved Custom application

LED H-4 6 volt bulb replaces H-4 bulbs in headlamp inserts. *NOTE: Plugs in directly. Custom application

3000k LED daylight bright white headlamp bulb with aluminum alloy shell is a H-4 30w 12 volt replacement with both hi and low beams. No need to replace the entire housing just replace the lamp with this LED bulb! Simple DIY retrofit kit for simple installation. Will fit 90% of motorcycles and most standard H4 bulb applications. Features 360° beam angle. Low draw won't drain the battery remains bright regardless of battery condition! Equipped with preset 15W high beam and 10W low beam. Life span of over 20 000 hours! **NOTE: NOT DOT approved. **NOTE: Due to the brightness of the
33-1718" Horn features a chrome 6 horn face with holes and an early style 6 volt wing grill horn with bracket. Custom for H-4 applications

LED headlamp adapter harness kit is used for installing Daymaker type LED headlamps. 2014-2018 FLT 2014-2018 FLHR 2014-2018 FLTRX

LED headlamp adapter harness kit is used to install Daymaker type LED headlamps. 2004-2013 FLTR

Wiring harness adapter allows the Cyron 7 LED headlamps to be intalled on 2014-up FLT models. 2014-UP FLT

Features red LEDs with 2 wires with nut to fit threaded body for a 7mm mounting hole. Wire is 10cm long. Lenses are 6mm in diameter. Housing outer diameter is 9.95mm. Custom application

Features red LEDs with 2 wires with nut to fit the threaded body. Wires are 10cm long. Lenses are 3mm in diameter. Housing diameter is 7.95mm Custom application

6000k LED daylight bright white headlamp bulb with aluminum alloy shell is a H-4 30w 12 volt replacement with both hi and low beams. No need to replace the entire housing just replace the lamp with this LED bulb! Simple DIY retrofit kit for simple installation. Will fit 90% of motorcycles and most standard H4 bulb applications. Features 360° beam angle. Low draw won't drain the battery remains bright regardless of battery condition! Equipped with preset 15W high beam and 10W low beam. Life span of over 20 000 hours! *NOTE: NOT DOT approved. **NOTE: Due to the brightness of the b
33-1783" Black 7 LED headlamp assembly features a LED halo ring that includes the daytime running light function. 1992-UP FXST 1992-UP FLST 1992-UP FLT 1992-UP XL 0-Replacement application for H4 bulbs

LED tail lamp assembly is constructed of brass aluminum billet and features a round style. Assembly includes a license bracket. Assembly is cast solid. May have pits and marks from the hand casting process. *NOTE: Product is sand cast by hand pits and imperfections are common with hand made parts . Custom application

LED tail lamp assembly is constructed of black aluminum billet and features a search light style. Assembly includes a license bracket. Custom application

LED tail lamp assembly is constructed of brass aluminum billet and features a search light style. Assembly includes a license bracket. *NOTE: Product is sand cast by hand pits and imperfections are common with hand made parts . Custom application

LED stop lamp with white LED. This stop lamp comes with 2 screws and is 1-1/2 long x 5 wide. *NOTE: For show or decorative use only and is not D.O.T. approved. Custom application