All

Smoked laydown style tail lamp lens with license plate lens facing down. 2003-UP FLT

Amber faceted lens set for stock and V-Twin bullet lamps. Sold as a pair. 1949-1985 FL

Green faceted lens set for stock and V-Twin bullet lamps. Sold as a pair. 1949-1985 FL

Purple faceted lens set for stock and V-Twin bullet lamps. Sold as a pair. 1949-1985 FL

Red faceted lens set for stock and V-Twin bullet lamps. Sold as a pair. 1949-1985 FL

Gary Bang beehive composite tail lamp mount gasket mounts between the tail lamp base and rear fender die cut of composition felt-paper material. Excellent use for restoration. 1939-1946 EL 1941-1946 FL 1939-1946 U 1939-1946 W

Tail lamp light socket for beehive style light includes wires as original. 1939-1946 WL 1939-1946 G 1939-1946 UL 1939-1940 EL

1936-1946 EL 1941-1946 FL

Tail lamp wire for beehive style tail lamps is cloth covered as original with socket fibre spring contacts and insulator. 1948-1957 EL 1948-1954 FL

Tail lamp wiring harness assembly has woven cloth wire. Tail lamp wires are red and green. 1947-1969 FLH

12 volt oval tail lamp with flat type glass lens included but not installed. The window is clear plastic. 1955-1972 FL 1957-1972 XL

Tamer clutch pull kit will soften the pull required on 1999-up Sportster models. The tamer replaces the stock Harley clutch on all of the 1999 to present Sporters. The pivot is moved closer to the center so the clutch lever is easier to pull for those who have difficulty holding their clutch while driving. A finger lock is in place to help better hold the clutch spring in place during the installation process. *NOTE: For use with the clutch outer ramp and the clutch ramp assembly. 1999-UP XL

Tap tool 1/4 x 24 is used for closed-end hole threading. 0-All Models

3/4 X 16 tap tool. 1936-1952 W 1936-1948 EL 1936-1957 G 1941-1948 FL

Original style convex mirror set for left and right side features long stems and a chrome finish. 0-All models

23 tooth tapered engine sprocket kit features a parkerized finish. Kit includes sprocket nut key dust seal collar and a retaining ring. The new tooling is meant for the exact fit and taper. 1936-1952 EL 1941-1954 FL

Tappet block screw kit with a cadmium finish. 1957-1985 XL

Tappet base bolt set of eight with 1/4 x 20UNC thread is nickel plated and has a hex shaped head. Screw does not have taper and fits 1976-up style lifter blocks only. Choose the correct thread type for your application. This set is for use on late model lifter blocks without tapered holes. 1948-1984 FL

Zinc plated non-threaded front and rear tappet block set. Set includes 2 front and 2 rear. 1939-1948 UL

Tappet screw and nut kit bolts are specifically threaded to replace both OEM 221-15 and 221-40A used on 1929-1973 Side Valves and 1952-1953 K models. 1929-1952 WL 1933-1973 G 1952-1953 K

4 piece tappet screw and locknut kit. 1957-1985 XL

4 piece tappet screw and locknut kit. 1936-1940 EL 1941-1952 FL 1937-1948 U

Tappet screw kit for TC-88 models includes eight screws with gaskets. 1999-2016 FLT 1999-2017 FXD 1999-2017 FXST 1999-2017 FLST

This inner cam bearing remover replaces the inner bearing easily without damage to crankcases and also prevents rollers from falling into the crankcase. For use with bearing as listed. The tool acts as a stable base to keep the camshaft perpendicular to the press. *NOTE: The shaft diameter before the flare measures 0.859 . 1999-2006 FXST 1999-2006 FLST 1999-2005 FXD 1999-2005 FLT

This four piece tool safely installs the inner cam bearings to the proper depth in the case without damaging bearings. Complete 8 piece tool by V Twin manufacturing. 1999-2006 FXST 1999-2006 FLST 1999-2006 FLT 1999-2005 FXD

TC-88 style motor keychain with silver patina finish. Motor plate is riveted in each corner to the leather backing. 0-All models

This oil change kit includes four quart 20W-50 full Synethic Spectro oil one quart 75W-140 Spectro 6-speed synthetic transmission oil one quart of Spectro primary oil oil filter and a primary service gasket kit. 2007-UP FXST 2007-UP FLST 2007-UP FLT 2006-2017 FXD

Daytona Twin Tec TCFI Gen 4 Auto Tune fuel injection controller is fully programmable plug in replacement for the 36 pin Delphi controller with J1850 data bus. Includes TCFI Gen 4 plug-in fuel injection controller with billet aluminum housing with black finish dual channel wide band exhaust gas oxygen sensor interface two Bosch LSU 4.2 wide band exhaust gas oxygen sensors and two 18 x 1.5mm weld nuts for exhaust pipes. Quickly auto-tune fuel curves for front and rear cylinders on a dyno or on-road. The rubust alpha-N fuel control eliminates problems with long duration/high over
32-7401" Daytona Twin Tec TCFI Gen 4 Auto Tune fuel injection controller is fully programmable plug in replacement for the 36 pin Delphi controller with J1850 data bus. Includes TCFI Gen 4 plug-in fuel injection controller with billet aluminum housing with black finish dual channel wide band exhaust gas oxygen sensor interface two Bosch LSU 4.2 wide band exhaust gas oxygen sensors and two 18 x 1.5mm weld nuts for exhaust pipes. Quickly auto-tune fuel curves for front and rear cylinders on a dyno or on-road. The rubust alpha-N fuel control eliminates problems with long duration/high over
32-7402" Daytona Twin Tec TCFI Gen 5 Auto Tune fuel injection controller is fully programmable plug in replacement for the 36 pin controller with CAN data bus. 2001-2011 FXST 2001-2011 FLST 2001-2011 FXD 2001-2011 FLT

2007-2013 XL

2012-UP FXST 2012-UP FLST 2012-2017 FXD

Tear drop air cleaner cover kit fits Velo or Screamin Eagle air cleaner kits. Kit is designed to fit all TC-88 and Evolution model equipped with a stage 1 kit with conical shaped air filter. Order filter separately. 1990-2017 FXST 1990-2017 FLST 1990-1994 FXR 1990-2006 FLT 1988-UP XL 1991-2017 FXD

Chrome billet apache style tear drop mirror set with offset stem. 1965-UP All models for left and right side application