Mid-USA

Slash Cut Drag Pipes, 2" Sportster 1986/2003 40" Long, Channel Mounting

• Top quality drag pipes for models listed
• Chrome plated or black primer that is suitable for heat wrapping. Black primer is a protectant for rust, not a ceramic heat coating
• Slash cut tips for a performance look
• Hidden channels for a clean look

V-FACTOR
2" Chrome Plated Set
Fits Evolution Sportster 1986/2003

Air Filter Element Flt Models 2008/Later* Rpls Hd 29633-08

• Engineered for increased performance
• Washable and reusable high flow 4-layer cotton element increases air flow while offering unmatched filtration for long engine life
• Not only will these filters increase horsepower in stock engines, they are a must when performance upgrades have been done your motorcycle
• Sold each

V-FACTOR
Air ilter Element, 1 3/4 width
Fits FLT models 2008/Later
Replaces HD# 29244-08

Bendix Carb Part, Rebuild Kit Bendix/Zenith 36,38 & 40Mm Replaces Hd 27132-71

• This kit includes all the parts necessary to properly rebuild your Bendix/Zenith carburetor to factory specifications
• Kit includes a three way adjustable accelerator pump

V-FACTOR
Fits all 36mm, 38mm and 40mm Bendix/Zenith carburetors
Replaces HD# 27132-71

Chuck the chain and bolt in the belt for a smoother ride with this 8mm Enclosed Primary Belt Drive Kit from Belt Drive Limited.
Designed for use without modification to the inner primary cover, these bolt-in kits feature cylindrical shaped, replaceable round clutch dogs which can withstand 1200 pounds of torque. The inner stress proof steel hub is designed to move the weight of the clutch basket inward over the mainshaft 1 inch which distributes the weight more evenly on the mainshaft. To ensure a low rotating weight and provide long life, both the front and rear pulleys are made of lightweight aluminum and are hard anodized. Rounding out these kits are a set of Kevlar^® clutch plates that provide 60% more surface area than the OE clutch and a Kevlar^® belt for positive performance. If more clutch plate pressure is needed, the pressure plate is designed to accept up to 6 more clutch springs if required. Each kit includes a sealed primary bearing (except kit 77028). A primary bearing seal is also included for those who don't want to change the OEM non-sealed style bearing. Change over today for a smoother, quieter ride.

Note: Due to the numerous variables of misalignment and improper tensioning upon installation, there is no warranty on belts.

Note: No modification is required to the inner primary for installation.

1-5/8" wide Belt Dive Kit with Clutch

Fits FLT & FXR models Late 1985/1989 with taper clutch hub and rear belt drive, 48-68 tooth combo

Sprocket,Trn.310"Offset Kit 24 Tooth Bt 4 Spd W/Disc Brake Sprocket & Wheel Spacer W/Hrdw
This Transmission Sprocket and Rear Sprocket Offset Spacer Kit eases the pain of installing wider rear tires. Kit includes a chrome plated rear sprocket spacer, .310 thick, and chrome mounting hardware designed for use with flange type steel rear wheel hub. When using on models with an open primary, a belt drive style transmission mainshaft bearing support must be used. When using electric start a rear belt drive style inner primary and appropriate starter motor must be used. As with any wide tire application always check all clearances.

Fits Big Twin 4 speed with rear disc.

24 Tooth Sprocket Kit. (Imported)

Cam Chain Tensioner Pad Kit Twin Cam 1999/2006

• Chain tensioner pads are an item overlooked and when they fail, major issues can occur
• These pads work on the inner and outer tenioners and are made from a high performance polymide stanyl that surpasses the OEM material
• Sold as a kit with one pad and one pin

Cam Chain Tensioner Pad Kit
Fits Twin Cam 1999/2006

Semi-Metalic Brake Pads Fr/Rr Gma Model"B",Jay Brake Adc & Adcs,Hardbody 2 Piston
This pair of Brake Pads are economically prices and designed to be used with small GMA calipers ADC & ADCS. The pad material is made from a semi-metallic, non-asbestos with a Kevlar base. Pad measures 1 5/8 long x 1 1/2 tall. Sold in pairs.V-FACTOR Brake Pads
Fits GMA Model B Two Piston (rear)
Fits L 4 speed 1949/1984 Custom, Converts Wide glide to Dual Disc. Use with dual lange Hub. Mounts to ender Lugs. May require removal of original factory brake Mounting Tab. Use with 10 flat rotor. XSTS Springer Softail 1988/Later and most Custom Springers, Paughco Wide Springer including our 35203, 35204, & 35205 Use 56228 Axle and 11 1/2 rotor. X and Sportster 1974/1977 Single Disc 19 wheel only, all Single Disc models 1984/1999 (except Springer & L 4 speed), and all Dual Disc models 1984/1999

Pro II Brk Sys Come Ferrule Vw45776/788 Fittings Only Brass Russell R49009

• Russell's Pro System II hose and fittings are designed for custom builders that need to easily fabricate brake or hydraulic clutch lines
• The cut to length semi-rigid black nylon hose has a ³/₁₆ O.D. for a low impact custom look yet provides improved braking effect with the same lever pressure as OE size hose. Hose is not DOT approved
• The chrome plated steel compression fittings (sold separately) are available to replace ³/₈-24 & ⁷/₁₆-24 banjo bolts as listed. The ¹/₈-27 NPT compression fittings are designed for early style or custom brake hoses drilled and tapped for pipe thread
• The 45870 male adapter end is designed for use with -3 male adapter banjo ends or brake tees found in the control section when required

Russell
Replacement Compression errules, Pack of 10

Rear Brake Master Cylinder St 00/L* & Touring 99/07 Rpls Hd 41755-99 & 41767-05A

• High quality reproduction of the OE part

V-FACTOR
Chrome Plated Rear Master Cylinder
Fits Softail 2000/Later & Touring models 1999/2007
Replaces HD# 41755-99 & 41767-05A

Foot Lever, Shift Chrome Sportster All Models 1986/1989 Rpls Hd 34606-86A & 34605-86T
These replacement foot shift levers meet or exceed the OEM specifications. See the control section for foot shift pegs.V-FACTOR
Chrome Plated oot Shift Lever
Fits Sportster & K Model 1986/1989
Replaces HD# 34606-86A & 34605-86T
(Imported)

Chrome Side Cover Trim Rails Fits Flh & Flt Models 1993-Later, 66064-93

• Mounts on the side covers of bagger models
• Manufactured from high quality steel
• Includes left and right trim rails and mounting hardware

V-FACTOR
Show Chrome Plated
Fits FLH & FLT models 1993/Later
Replaces HD# 66064-93
(Imported)

Fender Extension,Rear For Use W/22970&22971 Tri-Bar Lights Abs Chrome Plated

• 
  
  
  
  • Chrome plated ABS rear fender extension enables 22970 or 22971 to be fitted on FLHR & FLT models 1999/Later
  
  
  • Kit is easy to install and includes all necessary hardware
  
  
  
  

(Imported)

Spotlight And Passing Light Shell Only, 4-1/2" Bottom Mount W/Hardware, Chrome
These 12 volt 4 ¹/₂ O.D. Spotlight and Passing Light Assemblies are complete as shown and ready to bolt on. See below for availability of lens. V-FACTOR
Chrome Plated 4 ¹/₂ O.D. Shell Housing & Hardware without light
Fits Dresser models 1962/Later & custom use
Replaces HD# 68667-78

Taillight Lens,Rpls Lens On Maltese Cross Taillight #11212 And #11232, Bulb Or LED Type

• Sturdy die cast chrome plated housing has a flat back for easy mounting and includes 5/16 mounting bolts on 2 centers
• Taillight measures 4 tall x 4 1/8 wide and is 1 7/8 thick
• A clear license window is also provided
• 12 volt assemblies are available with an automotive #1157 bulb or with 53 separate LED lights

Note: These tailight assemblies are not DOT approved and should be used accordingly.V-FACTOR
Replacement Red Plastic Lens

Circuit Breaker, 15Amp All Models 73/Later Replaces Hd# 74589-73

• Plastic housing with mounting brackets are one piece molded designs and are less prone to vibration
• Metal housings with brackets are two piece designs
• Made in the USA

POWER HOUSE PLUS
15 amp metal
Replaces HD# 74589-73

Alternator Rotor Dyna 2006 Rpls Hd 40356-06
V-FACTOR
Heavy Duty Black Rotor
Fits Dyna 2006 with 40 Amp charging system
Replaces HD# 40356-06
(Imported)

Spark Plug Covers, Sparkies Blue Lens Fits All H-D Spark Plugs W/90 Degree Boots

• Designed to show your engine's spark through colored lenses at the base of the wire

V-FACTOR
Sparkies Spark Plug Cover Pair with Blue Lens
Fits all Harley-Davidson spark plugs with 90° boots
For 7mm or 8mm plug wires
Sold in pairs

(Imported)

Secondary Cam Chain Tensioner Big Twin 1999/2006 Rpls Hd 39964-99A
HARDWARE
Secondary Cam Chain Tensioner
Fits 1999/2006
Replaces HD# 39964-99A

Starter Shaft Needle Bearing See Oem # & Catalog For Fit Rpls Hd #9063 Torrington B1210
Torrington
B1210 Outer Primary Cover/Starter Shaft Needle Bearing
Fits L 1965/1982, FLT 1980/1988, FXR 1982/1988, X 1971/1984 (except XB & XSB), XE 1985, Softail 1984/1988 and Sportster, K model 1967/1980, Big Twin 5 speed 1980/1988
Replaces HD# 9063

Brake Tool Eze Bleeder All Models W/Hydraulic Brakes Complete W/Instructions

• Bleed your brakes easily and efficiently the first time with the EZE Brake Bleeder^®
• Developed by mechanics for mechanics, this kit utilizes the law of physics by back bleeding the brake system pushing air in Fits natural direction up to the master cylinder
• Holds 40cc of brake fluid
• Includes sealed container for storage and instructions

Eze Bleeder
Includes adapters for 1/4 & 3/8 brake bleeder screws

Intake Manifold Adapter, Flange 40/44Mm Spigot Carb To 2 Bolt Flange Mount Intake Manifold
These gas resistant neoprene Intake Manifold Adapters are used to mount Mikuni and Lectron spigot style carburetors. They are available for mounting to a spigot type intake manifold or for mounting to a 2-bolt flange type manifold. V-FACTOR
Flange Type for 40/44mm carburetor
Bolt holes on 3 ⁵/₁₆ centers designed for custom 2 hole flange type intake manifold, 1 ¹³/₁₆ I.D.
Includes clamp, (Imported)

Flush mount replacement cap. Fits MID-80024 Bung Kit

• Vented gas cap pops up for easy removal and mounts flush in the down position
• Cap measures 1 ⁵/₈ O.D.

V-FACTOR
Replacement Chrome Plated Flush Mount Gas Cap with O-Ring Only

2" Primary Drive Belt, 8mm X 140T, BDL-140-2
All replacement primary belts are fiberglass reinforced HTD type rubber belts (except 77511, 77548 & 77533 that are KEVLAR® reinforced) supplied to us straight from the manufacturer to ensure a positive fit every time. If the needed belt length is not known, determine the number of pulley teeth combination and width for the correct belt.

Belt Drives Ltd.
Replacement Belt (2" Wide, 8mm, 140 Tooth) 48 & 69 Pulley Teeth Combo
Fits 1990/2006 Softail Signature Series

Note: Due to the numerous variables of misalignment and improper tensioning upon installation, there is no warranty on belts.

All replacement primary belts are fiberglass reinforced HTD type rubber belts (except 77511, 77548 & 77533 that are KEVLAR® reinforced) supplied to us straight from the manufacturer to ensure a positive fit every time. If the needed belt length is not known, determine the number of pulley teeth combination and width for the correct belt.
Belt Drives Ltd.
Replacement 1 ⁵/₈" wide Kevlar Reinforced Belt
Fits 45-68 tooth combination - 138 teeth
Fits Big Twin 5 speed Late 1985/Later with electric start

Note: Due to the numerous variables of misalignment and improper tensioning upon installation, there is no warranty on belts.