All

Final drive steel 29 tooth front pulley. Order nut spacer and lock tab separately. 2004-UP XL

Chrome 29-1/2 straight fishtail muffler with scalloped end has a 1-7/8 diameter to fit 1-3/4 pipes. These are straight through without baffles. Order clamps and baffles separately. Check with your local state to see if approved for street use. **CAUTION: These exhaust products are not legal for sale or use in California on pollution controlled vehicles. These products are intended for non-highway only. Custom application for 1-3/4 exhaust pipes"

Black 2:1 exhaust header set features lake style 3" big diameter turn out ends that are baffled, full coverage chrome heat shields and 1-3/4" header tubes.
Turn out end is clamped on and will allow the installer to rotate into the desired position.

*NOTE: Maximize your motorcycles' performance and efficiency by complementing your new Wyatt Gatling exhaust system with a fuel turner management system and or EFI remapping. Remapping is suggested to optimize performance while reducing the possibility of damage to your motor or new exhaust system. Includes 10mm Delphi Sensor Bung.

**NOTE: Must order rear footpeg spacer separately.
**NOTE: End is lake type profiled oval. Tucks in close to saddlebag and side cover.
**NOTE: The footboard spacer with lock pin VT-31-1318 may be required.

1986-UP XL

Chrome 2:1 siamese exhaust header set with a 1-3/4 outer diameter fits under the carburetor on rigid or swingarm frames. *NOTE: Pipe is a welded one piece unit. Muffler header and pipe clamps not included. **NOTE: Extension of the rear pipe fits over the front pipe and is clamped with an integral clamp to secure. ***NOTE: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. *CAUTION: These exhaust products are not legal for sale or use in California on pollution controlled vehicles. These
29-0204" Black 2:1 siamese exhaust hi-header set with a 1-3/4 outer diameter fits under the carburetor on rigid or swingarm frames and features a one piece design for Ironheads only. *NOTE: Pipe is a welded one piece unit. Muffler header and pipe clamps not included. **NOTE: Extension of the rear pipe fits over the front pipe and is clamped with an integral clamp to secure. ***NOTE: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. *CAUTION: These exhaust products are not legal for sale or use
29-0206" Chrome 2:1 siamese exhaust header set with a 1-3/4 outer diameter fits under the carburetor on rigid or swingarm frames. 1957-1985 XL

1957-1985 XL

2nd gear for countershaft 24 tooth stock ratio fits 4- speed Big Twin models. 1980-1985 FX 1980-1985 FXWG 1984-1985 FXST

2nd gear retaining bracket. Includes OEM #35335-41 lock tab and two OEM #3754 hex screws. Hex screws measures 1/4 x 24 x 21/32 long with a 7/16 hex head. 1941-1973 G 1941-1952 W

3 black face retro mirror kit includes early type steel stamped stem with black oxide finish. Fits 1 bar. 0-All models

Riser stems are chrome plated steel and have a 3/4-16UNF thread to screw into spring fork rear legs. The spring fork rear legs must be threaded to accept risers. Use tops and bushings from existing Flanders risers. Requires use of 3/4 -16UNF tap. Installation of these riser stems requires tapping of the rear leg tubes to 3/4 x 16 for mounting. 1936-1957 G 1936-1952 W 1941-1948 FL 1936-1948 EL 1937-1948 U

Wyatt chrome 3 post riser set steel have 1/2 X 20 internal threads for mounting Custom application

1993-2013 FLT

3 stretched saddlebag kit includes bags lids locks and mounting hardware. Bags are injection molded and have a smooth inside and outside surface. Bottoms are 2 deeper in th front 3 deeper in the rear and have cutouts on both bags for dual exhaust. All pieces are constructed of FRP fiberglass reinforced plastic ready for primer and paint. FRP is made up of polyphenylene oxide/polyamide alloy. Face plate is not included in this kit. 2014-UP FLT

Vintage 1 diameter handlebar has a rise of 3 are chrome plated and has holes for internal wiring and notched for throttle by wire applications. 1982-1984 FL 1982-1984 FX 1982-UP XL 1984-2017 FXST 1986-2017 FLST

1 chrome z handlebar with indents are pre drilled for internal wiring. The grips drop below the top triple tree because of the shape and can also be rotated forward to create a different look. *NOTE: Must order installation hardware separately. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 2010-UP XL except 2011-up XL883L

1 satin black z handlebar with indents are pre drilled for internal wiring. The grips drop below the top triple tree because of the shape and can also be rotated forward to create a different look. *NOTE: Must order installation hardware separately. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 2010-UP XL except 2011-up XL883L

Linkert 38mm carburetor adapter kit includes a three bolt adapter intake manifold rubber adapter and two stainless steel hose clamps. Order intake manifold separately. 1937-1948 UL 1935-1952 WL

3 skull billet mirror includes wing stem. Use for right or left sides. 1965-UP All models for left or right side application

3 skull billet mirror includes worm stem. Use for right or left sides. 1965-UP All models for left or right side application

3-1/2 Nylon petcock screen for use with male thread petcock. Screen measures 3-1/2 long. 1995-2001 FXST 1995-2001 FLST 1995-2001 FLT 1995-2001 FXD

Chrome short riser set are 3-1/2 high and fit 1 bars. Custom application for 1 handlebars"

Piston set with 3-5/16 bore is .030 oversize. Set includes Hasting 3 piece ring 2 wrist pins and 4 circlips. Pistons have a steel expansion control strut cast. **NOTE:Run engine at moderate speeds for at least 500 miles avoiding excessive running in lower gears in order to properly break-in new pistons and rings. 1936-1940 EL

Cylinders are stock height. For installation of 3-5/8 cylinders after spigot holes have been enlarged. (See diagram for photos.) *NOTE: 3-5/8 cylinders are drilled to use with 4-1/2 and 4-1/4 stroke. Will require break in as suggested in the shop manual. These are cylinders only. Order pistons and rings separately. These cylinders will require crankcase cylinder spigot holes to be bored out. Disassmbly of engine is required to install these cylinders. NOTE: The finished bore size should be 3.6270 . 1966-1984 FL 1971-1984 FX 1979-1983 FLT 1982-1983 FXR

Negative brush holder assembly is for three brush generators. Assembly is constructed of three pieces riveted together. 1936-1952 EL 1941-1957 FL

Inner oil retainer has a zinc plated finish. 1932-1936 VL 1937-1948 UL 1936-1940 EL 1941-1951 FL 1952-1952 W 1952-1952 G

This 3-brush generator pole screw kit has a parkerized finish. 1936-1940 EL 1941-1957 FL 1930-1934 VL 1937-1948 UL

Made of 8620 steel with .120 heat treatment and is 3-hole type. 1957-1980 XL

Crank pins are made of 8620 steel with .062 heat treated penetration. Crank pin is .010 oversize 3-hole type. 1940-1952 EL 1940-1948 UL

Chrome steel with black mesh 3 hole outer primary derby cover. 1970-1984 FL 1971-1984 FX 1984-1984 FXST 1985-1998 FXST 1986-1998 FLST 1984-1984 FLT 1985-1998 FLT 1991-1998 FXD 1984-1984 FXR 1985-1994 FXR

3-LITE BASE W/WIRING SOCKET

3-slot chrome brake pedal. Includes grease fitting. Order pedal rubber separately. 2008-2013 FLT

Our V-Twin 21 tire tubes are manufactured with 100% natural rubber and meet or exceed OEM quality and performance. The tire tube features an all metal constructed center valve. 0-Front

Center valve inner tube with metal stem. 0-Front or Rear